淘宝买的机顶盒用DT-7103HD.CPU用的BCM 7358有TTL输出

caoximing

在淘宝上看到一个机顶盒（卫星接收器）28元包邮。BCM7358的cpu 256M内存 128M闪存，国外的。打家看看能不能刷个什么。卖家在别的论坛出3万求固件。看下各位大侠能搞出来不。弄几张图片过来了，带2个USB接口



#!@#@Linux version 2.6.37-2.8+ (gert-jan@broadcom1) (gcc version 4.5.3 (Broadcom stbgcc-4.5.3-1.3) ) #4 Thu Jan 17 14:19:05 CET 2013
Fetching vars from bootloader... found 3 vars.
Options: enet_en=1 enet0_mii=0 enet_no_mdio=0 enet1_en=0 moca=0
         sata=0 docsis=0 pci=0 pcie=0 smp=0 usb=1
Probing system memory size... found 256 MB
CPU revision is: 00029032 (Broadcom BMIPS3300)
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
bmem: adding 146 MB RESERVED region at 110 MB (0x09200000@0x06e00000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00010000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00010000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: root=/dev/romblock1 rootfstype=squashfs ro bmem=146M@110M
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 105468k/262144k available (3812k kernel code, 156676k reserved, 767k data, 184k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 501 MHz (250.503 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop... 499.71 BogoMIPS (lpj=249856)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
USB0: IOC was not set by the bootloader; forcing default settings
USB0: power enable is active low; overcurrent is active low
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource wktmr
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 205
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x10406840 (irq = 63) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10406880 (irq = 64) is a 16550A
brd: module loaded
loop: module loaded
brcmstb_nand: NAND controller driver is loaded
Config internal EPHY through MDIO
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
belkin_sa: v1.3:USB Belkin Serial converter driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
TCP cubic registered
NET: Registered protocol family 17
EBI CS2: setting up NAND flash (primary)
NAND device: Manufacturer ID: 0x98, Chip ID: 0xd1 (Toshiba NAND 128MiB 3,3V 8-bit)
brcmnand brcmnand.0: 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4

Scanning device for bad blocks
RedBoot partition parsing not available

BB Check: Number of partitions 3

BB Check: Checking Partition - "l", 100 blocks to check

BB Check: l -> Offset = 0x00000000, size = 0x00c80000 (12 MB)

BB Check: Checking Partition - "r", 508 blocks to check

BB Check: r -> Offset = 0x00c80000, size = 0x03900000 (57 MB)

BB Check: Number of Bad Blocks found - 0
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000000c80000 : "l"
0x000000c80000-0x000004580000 : "r"
0x000004c00000-0x000008000000 : "s"
EBI CS0: setting up SPI flash
spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
m25p80 spi0.0: found w25x40, expected m25p80
m25p80 spi0.0: w25x40 (512 Kbytes)
PM: CP0 COUNT/COMPARE frequency depends on divisor
VFS: Mounted root (squashfs filesystem) readonly on device 253:1.
Freeing unused kernel memory: 184k freed
Algorithmics/MIPS FPU Emulator v1.5
starting pid 341, tty '': '/etc/init.d/rcS'
Mounting virtual filesystems
mount: mounting debugfs on /proc/sys/debug failed: No such device
Starting mdev
Configuring eth0 interface
eth0 cable plugged in, powering up
Configuring lo interface
Starting network services
/etc/init.d/rcS: line 76: telnetd: command not found
/etc/init.d/rcS: line 75: portmap: command not found
Starting user services
if you want to have the demo date and time, type 'date -s 2008.7.10-9:50' before running the smartGuide
(another date that was used was: 'date -s 2007.8.8-18:30')
chown: /local: Read-only file system
chmod: /local: Read-only file system
Detected storage mtd: -2-
ubidetach: error!: cannot detach mtd2
           error 19 (No such device)
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: max. sequence number:       21
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "s"
UBI: MTD device size:            52 MiB
UBI: number of good PEBs:        416
UBI: number of bad PEBs:         0
UBI: number of corrupted PEBs:   0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 416
UBI: number of PEBs reserved for bad PEB handling: 4
UBI: max/mean erase counter: 2/1
UBI: image sequence number:  -820707178
UBI: background thread "ubi_bgt0d" started, PID 402
UBI device number 0, total 416 LEBs (52822016 bytes, 50.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "s"
UBIFS: file system size:   50663424 bytes (49476 KiB, 48 MiB, 399 LEBs)
UBIFS: journal size:       2539520 bytes (2480 KiB, 2 MiB, 20 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  2392958 bytes (2336 KiB)
Load module 'bcmdriver' (nexus in user mode)
bcmdriver: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
BCMDRV: Initializing bcmdriver version $ 36 $
BCMDRV: Total intc words=3,Total Irqs=97
BCMDRV: Global Interrupt Mask 0:0x308000FF,1:0x1FE387F7,2:0x8013FC00,3:0x00000000
BCMDRV: Initialization complete...
cp: can't create '/sbin/stbhotplug': File exists
Verifying interface to devices
Virtual IP driver to communicate with tuner not ready yet
type break to skip this check
eth0 cable unplugged, powering down
Starting up ...

IP configuration information:
=============================================================================
eth0      Link encap:Ethernet  HWaddr 00:10:05:22:12:ED
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encapocal Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

=============================================================================
usb 1-1: new high speed USB device using ehci-brcm and address 2
scsi0 : usb-storage 1-1:1.0
scsi 0:0:0:0: Direct-Access     USB2.0   Flash Disk       2.60 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 512768 512-byte logical blocks: (262 MB/250 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda:
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
if you want to have the demo date and time, type 'date -s 2008.7.10-9:50' before running the smartGuid(another date that was used was: 'date -s 2007.8.8-18:30'Calling fdisk on /dev/sda
usb 1-1: USB disconnect, address 2
if you want to have the demo date and time, type 'date -s 2008.7.10-9:50' before running the smartGuid(another date that was used was: 'date -s 2007.8.8-18:30'Calling fdisk on /dev/sda
#!@#@Linux version 2.6.37-2.8+ (gert-jan@broadcom1) (gcc version 4.5.3 (Broadcom stbgcc-4.5.3-1.3) ) #4 Thu Jan 17 14:19:05 CET 2013
Fetching vars from bootloader... found 3 vars.
Options: enet_en=1 enet0_mii=0 enet_no_mdio=0 enet1_en=0 moca=0
         sata=0 docsis=0 pci=0 pcie=0 smp=0 usb=1
Probing system memory size... found 256 MB
CPU revision is: 00029032 (Broadcom BMIPS3300)
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
bmem: adding 146 MB RESERVED region at 110 MB (0x09200000@0x06e00000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00010000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00010000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: root=/dev/romblock1 rootfstype=squashfs ro bmem=146M@110M
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 105468k/262144k available (3812k kernel code, 156676k reserved, 767k data, 184k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 500 MHz (250.497 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop... 499.71 BogoMIPS (lpj=249856)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
USB0: IOC was not set by the bootloader; forcing default settings
USB0: power enable is active low; overcurrent is active low
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource wktmr
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 205
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x10406840 (irq = 63) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10406880 (irq = 64) is a 16550A
brd: module loaded
loop: module loaded
brcmstb_nand: NAND controller driver is loaded
Config internal EPHY through MDIO
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
belkin_sa: v1.3:USB Belkin Serial converter driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
TCP cubic registered
NET: Registered protocol family 17
EBI CS2: setting up NAND flash (primary)
NAND device: Manufacturer ID: 0x98, Chip ID: 0xd1 (Toshiba NAND 128MiB 3,3V 8-bit)
brcmnand brcmnand.0: 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4

Scanning device for bad blocks
RedBoot partition parsing not available

BB Check: Number of partitions 3

BB Check: Checking Partition - "l", 100 blocks to check

BB Check: l -> Offset = 0x00000000, size = 0x00c80000 (12 MB)

BB Check: Checking Partition - "r", 508 blocks to check

BB Check: r -> Offset = 0x00c80000, size = 0x03900000 (57 MB)

BB Check: Number of Bad Blocks found - 0
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000000c80000 : "l"
0x000000c80000-0x000004580000 : "r"
0x000004c00000-0x000008000000 : "s"
EBI CS0: setting up SPI flash
spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address
m25p80 spi0.0: found w25x40, expected m25p80
m25p80 spi0.0: w25x40 (512 Kbytes)
PM: CP0 COUNT/COMPARE frequency depends on divisor
VFS: Mounted root (squashfs filesystem) readonly on device 253:1.
Freeing unused kernel memory: 184k freed
Algorithmics/MIPS FPU Emulator v1.5
starting pid 341, tty '': '/etc/init.d/rcS'
Mounting virtual filesystems
mount: mounting debugfs on /proc/sys/debug failed: No such device
Starting mdev
Configuring eth0 interface
eth0 cable plugged in, powering up
Configuring lo interface
Starting network services
/etc/init.d/rcS: line 75: portmap: command not found
/etc/init.d/rcS: line 76: telnetd: command not found
Starting user services
if you want to have the demo date and time, type 'date -s 2008.7.10-9:50' before running the smartGuide
(another date that was used was: 'date -s 2007.8.8-18:30')
chown: /local: Read-only file system
chmod: /local: Read-only file system
Detected storage mtd: -2-
ubidetach: error!: cannot detach mtd2
           error 19 (No such device)
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: max. sequence number:       23
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "s"
UBI: MTD device size:            52 MiB
UBI: number of good PEBs:        416
UBI: number of bad PEBs:         0
UBI: number of corrupted PEBs:   0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 416
UBI: number of PEBs reserved for bad PEB handling: 4
UBI: max/mean erase counter: 2/1
UBI: image sequence number:  -820707178
UBI: background thread "ubi_bgt0d" started, PID 402
UBI device number 0, total 416 LEBs (52822016 bytes, 50.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "s"
UBIFS: file system size:   50663424 bytes (49476 KiB, 48 MiB, 399 LEBs)
UBIFS: journal size:       2539520 bytes (2480 KiB, 2 MiB, 20 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  2392958 bytes (2336 KiB)
Load module 'bcmdriver' (nexus in user mode)
bcmdriver: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
BCMDRV: Initializing bcmdriver version $ 36 $
BCMDRV: Total intc words=3,Total Irqs=97
BCMDRV: Global Interrupt Mask 0:0x308000FF,1:0x1FE387F7,2:0x8013FC00,3:0x00000000
BCMDRV: Initialization complete...
cp: can't create '/sbin/stbhotplug': File exists
Verifying interface to devices
Virtual IP driver to communicate with tuner not ready yet
type break to skip this check
eth0 cable unplugged, powering down
Starting up ...

IP configuration information:
=============================================================================
eth0      Link encap:Ethernet  HWaddr 00:10:05:22:12:ED
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encapocal Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

=============================================================================这下面是我接了U盘和PL2303串口出来的输出
usb 2-2: new full speed USB device using ohci-brcm and address 2
pl2303 2-2:1.0: pl2303 converter detected
usb 2-2: pl2303 converter now attached to ttyUSB0
usb 2-2: USB disconnect, address 2
pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
pl2303 2-2:1.0: device disconnected
usb 2-1: new full speed USB device using ohci-brcm and address 3
pl2303 2-1:1.0: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB0
usb 2-1: USB disconnect, address 3
pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
pl2303 2-1:1.0: device disconnected
usb 2-1: new full speed USB device using ohci-brcm and address 4
pl2303 2-1:1.0: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB0
usb 2-1: USB disconnect, address 4
pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
pl2303 2-1:1.0: device disconnected
usb 2-2: new full speed USB device using ohci-brcm and address 5
usb 2-2: USB disconnect, address 5
usb 2-1: new full speed USB device using ohci-brcm and address 6
usb 2-1: USB disconnect, address 6
eth0 cable plugged in, powering up
eth0 Link UP.
Auto config phy
eth0: Link is up, 100 Mbps Full Duplex
eth0 Link DOWN.
eth0 cable unplugged, powering down
eth0 cable plugged in, powering up
eth0 Link UP.
Auto config phy
eth0: Link is up, 100 Mbps Full Duplex
eth0 Link DOWN.
eth0 cable unplugged, powering down
eth0 cable plugged in, powering up
eth0 Link UP.
Auto config phy
eth0: Link is up, 100 Mbps Full Duplex
usb 2-2: new full speed USB device using ohci-brcm and address 7
pl2303 2-2:1.0: pl2303 converter detected
usb 2-2: pl2303 converter now attached to ttyUSB0
usb 2-2: USB disconnect, address 7
pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
pl2303 2-2:1.0: device disconnected
eth0 Link DOWN.
eth0 cable unplugged, powering down
eth0 cable plugged in, powering up
eth0 Link UP.
Auto config phy
eth0: Link is up, 100 Mbps Full Duplex
usb 1-2: new high speed USB device using ehci-brcm and address 8
scsi0 : usb-storage 1-2:1.0
scsi 0:0:0:0: Direct-Access     USB Mass  Storage Device  1.00 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] Attached SCSI removable disk
if you want to have the demo date and time, type 'date -s 2008.7.10-9:50' before running the smartGuid(another date that was used was: 'date -s 2007.8.8-18:30'Calling fdisk on /dev/sda

guyueno

这盒子特点蛮多的，可惜没能力玩。

共5000渠道和保存
2种语言（英语，土耳其语）
定时录像功能
直播节目停止/表（时间转换）功能
能够创建不同的收藏频道列表
能够锁定与密码功能所需的通道
当前/下一个节目信息（EPG支持）
多语言支持（25）
数字音频输出（光纤SPDIF）
恢复为出厂设置是
TV SCART输出
HDMI输出
模拟音频输出（通过SCART）
建立提示功能中的期望的节目
U盘连接
C波段3.7 - 4.2GHz的
Ku波段：10.7 - 12.7 GHz的
LNB控制信号：水平/垂直极化
开关（18 / 13V +/- 7.5％），0-22千赫
开关，音爆的A / B切换
信号电平与信号质量的显示
自动频道命名
静音（静音）和音量控制
从软件更新卫星（OAD）
数字解码功能：
→解调方式：
QPSK，DVB-S 1-45Msym / s的
QPSK，DVB-S2 2-45Msym / s的
8PSK 2-45Msym /秒
8PSK Turbo 2-30Msym /秒
→FEC模式：
自动QPSK，1/2，3/5，2/3，3/4，4/5，5/6，8/9，9/10
自动8PSK 3/5，2/3，3/4，5/6，8/9，9/10
QPSK（8PSK Turbo）自动，1/2，2/3，3/4，5/6，7/8
8PSK（8PSK Turbo）自动，2/3，3/4，4/5，5/6，8/9
→图像解码器：MPEG4; MPEG2，PAL / NTSC，
4：3/16：9
→声音解码：MPEG I级和II，32 / 44.1 / 48
kHz采样频率，单，双声道立体声及联合
立体声
→OSD分辨率（OSD）576I（SCART）720p（HDMI）
→视频输出：PAL（SCART）
Digiturk IQ功能

CNsign

修好三万？这玩意多少钱？

寻丶那一丝醉意

CNsign 发表于 2015-11-5 20:41
修好三万？这玩意多少钱？

估计奸商手里货不少能刷进去就能卖高价就赚了

CNsign

寻丶那一丝醉意 发表于 2015-11-5 20:47
估计奸商手里货不少能刷进去就能卖高价就赚了

走私的电子产品？你买了可以看电视？这是智能盒子吗？你的都可以刷进去买给你他哪里来的固件为什么嗨要求、

侏罗纪

寻丶那一丝醉意 发表于 2015-11-5 20:47
估计奸商手里货不少能刷进去就能卖高价就赚了

我在数码也看见了！

caoximing

CNsign 发表于 2015-11-5 21:18
走私的电子产品？你买了可以看电视？这是智能盒子吗？你的都可以刷进去买给你他哪里来的固件为什么嗨要求 ...

不可以，什么都不能用，就是能启动，有画面，没有遥控器。那个商家手里有几千台，所以想找人破解制作固件，出价3万让高手制作这个盒子的固件。后面一直没人做出来，所以就低价出了

caoximing

寻丶那一丝醉意 发表于 2015-11-5 20:47
估计奸商手里货不少能刷进去就能卖高价就赚了

不可以，什么都不能用，就是能启动，有画面，没有遥控器。那个商家手里有几千台，所以想找人破解制作固件，出价3万让高手制作这个盒子的固件。后面一直没人做出来，所以就低价出了

caoximing

CNsign 发表于 2015-11-5 20:41
修好三万？这玩意多少钱？

不是修好3万。是那个商家手里有几千台货，想找人破解制作固件，出价3万让高手制作这个盒子的固件。后面一直没人做出来，所以就低价出了

mamiko

二十的不包邮

眼残了我

caoximing

mamiko 发表于 2015-11-5 21:59
二十的不包邮

眼残了我

是20元一台，8元邮费。所以就28包邮啦

mamiko

caoximing 发表于 2015-11-5 22:03
是20元一台，8元邮费。所以就28包邮啦

悬赏都没人搞了。估计是不好弄
做工是够屌

nengquan3

硬件太垃圾，机顶盒几十一台的安卓系统比这枪百倍，这洋垃圾起码四五年前的了