ubnt解决方案
查看: 2131|回复: 8

[教程] fir302b fw网页升级失败 TTL刷回

[复制链接]

123

回帖

4659

积分

416 小时

在线时间

少校

注册时间
2012-2-24
金币
4446 个
威望
8 个
荣誉
0 个
累计签到:444 天
连续签到:0 天
[LV.730]常住居民
发表于 2014-10-29 14:29 |显示全部楼层
最近从朋友那边看到一个fir302b的路由没人用放在那觉得可惜,原因玩的时候会卡。反正没人用拿回来刷刷看。
一开始用 海蜘蛛 按照他的说明来的用的webs升级。才上上去就没用了。。折腾了好几天看看有没有不拆机可以刷回的方法。
不过怎么试都没用设备死活不响应。
无奈只能拆开焊排针。

下面来说下刷机经验。
看来好多帖子。
1.有串口的情况先 按住键盘ctrl+c 不然进不去。
2.进去后打 flash -noheader 【tftp地址】:/[文件名] flash1.trx
3.等待出现如下字
done. 3969024 bytes written
*** command status = 0
CFE>

4.拔网线后reboot
Cisco TFTP Server 和 镜像 在附件有
下面列出串口log
======================================================================
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
骵rial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Found an ST compatible serial flash with 64 64KB blocks; total size 4MB
Creating 5 MTD partitions on "sflash":
0x00000000-0x00020000 : "pmon"
0x00020000-0x003f0000 : "linux"
0x000fa400-0x003f0000 : "rootfs"
0x003f0000-0x00400000 : "jffs2"
0x003f0000-0x00400000 : "nvram"
_nvram_init: allocat header: 2166259712, size= 32768
u32 classifier
    OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Sep 10 2014 16:15:53]
create dev playmud.gmail.com sucessed
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
Unhandled kernel unaligned access[#1]:
Cpu 0
$ 0   : 00000000 00000000 ffffffff 000001ff
$ 4   : 8027e8dc 00000000 00000000 00000000
$ 8   : 00000000 00000000 fffffffa ffffffff
$12   : ffffffff 00000008 00000008 ffffffff
$16   : 8110f6a0 00000001 00000000 00000400
$20   : 00000bb8 00000000 81115ba0 00000000
$24   : 00000002 8005c168                  
$28   : 8110e000 8110f620 8110f790 800ac22c
Hi    : 00000000
Lo    : 02625a00
epc   : 800ac278     Not tainted
ra    : 800ac22c Status: 11008003    KERNEL EXL IE
Cause : 00000010
BadVA : 0000014b
PrId  : 00019749
Modules linked in:
Process swapper (pid: 1, threadinfo=8110e000, task=8110cc00)
Stack : 80311308 00000002 802ea000 8110f6a0 00000400 00000001 811f2200 811f2000
        811f2000 8110f6a0 002edf77 00000000 8110f790 800ae8dc 8110f6a0 00000001
        811f2200 811f2000 802e8000 8110f6a0 002edf77 00000000 8110f790 800d3edc
        00000001 00000000 00000000 811e48ac 00000400 802f5540 00000000 00000002
        80311988 80311308 80311348 80311388 803113c8 80311ec8 80311f08 80311f48
        ...
Call Trace:[<800059f8>][<80006944>][<80006dc8>][<80281754>][<80001548>][<802815bc>]

Code: 8c420038  10400005  240301ff <9442014c> 14400002  2443ffff  240301ff  00731024  14400006
Kernel panic - not syncing: Attempted to kill init!
Decompressing...done


CFE version 5.100.138.2205 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Sat Jan 11 15:58:50 CST 2014 (guojianping@Server-SW-X03)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 64 64KB blocks; total size 4MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.2205
CPU type 0x19749: 300MHz
Tot mem: 32768 KBytes

CFE mem:    0x80700000 - 0x80799430 (627760)
Data:       0x8072EFA0 - 0x807321F0 (12880)
BSS:        0x807321F0 - 0x80733430 (4672)
Heap:       0x80733430 - 0x80797430 (409600)
Stack:      0x80797430 - 0x80799430 (8192)
Text:       0x80700000 - 0x8072EF98 (192408)

Device eth0:  hwaddr F0-EB-D0-63-6D-CD, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
***Press <Ctrl+C> key enter boot command line.***
Startup canceled
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE> ^C
CFE>
CFE>
CFE>
CFE> ls
Invalid command: "ls"
Available commands: mac, dp, nvram, reboot, flash, batch, go, boot, load, upload, save, ping, arp, ifconfig, unsetprienv, getprienv, setprienv, show, help
*** command status = -1
CFE> admin
Invalid command: "admin"
Available commands: mac, dp, nvram, reboot, flash, batch, go, boot, load, upload, save, ping, arp, ifconfig, unsetprienv, getprienv, setprienv, show, help

*** command status = -1
CFE> flash -noheader 192.168.1.3:/vmlinuz flash.trx
flash.trx: Device not found
*** command status = -6
CFE> flash -noheader 192.168.1.3:/vmlinuz flash1.trx
Reading 192.168.1.3:/vmlinuz: Done. 3969024 bytes read
Programming...
done. 3969024 bytes written
*** command status = 0
CFE> ftp
Invalid command: "ftp"
Available commands: mac, dp, nvram, reboot, flash, batch, go, boot, load, upload, save, ping, arp, ifconfig, unsetprienv, getprienv, setprienv, show, help

*** command status = -1
CFE> reboot
Decompressing...done


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?注册 微信登录

x
不错哦哈哈。

1790

回帖

1万

积分

2020 小时

在线时间

上校

注册时间
2014-2-22
金币
12774 个
威望
1 个
荣誉
0 个
累计签到:1252 天
连续签到:0 天
[LV.1825]无线元老
发表于 2014-10-29 14:37 |显示全部楼层
用编程器最简单。


回复

使用道具 举报

123

回帖

4659

积分

416 小时

在线时间

少校

注册时间
2012-2-24
金币
4446 个
威望
8 个
荣誉
0 个
累计签到:444 天
连续签到:0 天
[LV.730]常住居民
发表于 2014-10-29 14:40 |显示全部楼层
信诚 发表于 2014-10-29 14:37
用编程器最简单。

编程器要下东西呢。。而且没那技术哎。
不错哦哈哈。
回复

使用道具 举报

1790

回帖

1万

积分

2020 小时

在线时间

上校

注册时间
2014-2-22
金币
12774 个
威望
1 个
荣誉
0 个
累计签到:1252 天
连续签到:0 天
[LV.1825]无线元老
发表于 2014-10-29 15:02 |显示全部楼层
本帖最后由 信诚 于 2014-10-29 15:04 编辑
ailangzhou 发表于 2014-10-29 14:40
编程器要下东西呢。。而且没那技术哎。

可能错在flash -noheader 192.168.1.3:/vmlinuz flash1.trx
  "/" 上。


论坛中有编程器固件的。


我也有302B刷W3000R的固件。


只要能拆下FLASH来,上编程器就简单多了,复杂的是焊与拆焊
941 V5.1 刷DD后发射功率也没变大。
个人感觉家用改大内存意义不大32MB够用
回复

使用道具 举报

241

回帖

1891

积分

222 小时

在线时间

上尉

注册时间
2014-7-28
金币
1616 个
威望
1 个
荣誉
0 个
累计签到:158 天
连续签到:0 天
[LV.200]无线新星
发表于 2014-10-29 15:24 |显示全部楼层
高手,馍观中..........
回复

使用道具 举报

123

回帖

4659

积分

416 小时

在线时间

少校

注册时间
2012-2-24
金币
4446 个
威望
8 个
荣誉
0 个
累计签到:444 天
连续签到:0 天
[LV.730]常住居民
发表于 2014-10-29 15:25 |显示全部楼层
信诚 发表于 2014-10-29 15:02
可能错在flash -noheader 192.168.1.3:/vmlinuz flash1.trx
  "/" 上。

嗯 是的焊接没那技术真不敢弄。。
不错哦哈哈。
回复

使用道具 举报

21

回帖

181

积分

44 小时

在线时间

上等兵

注册时间
2014-11-27
金币
149 个
威望
1 个
荣誉
0 个
累计签到:14 天
连续签到:0 天
[LV.20]漫游旅程
发表于 2014-12-18 18:30 |显示全部楼层
恩 或许吧
回复

使用道具 举报

238

回帖

1322

积分

89 小时

在线时间

上尉

注册时间
2014-12-17
金币
1048 个
威望
3 个
荣誉
1 个
累计签到:76 天
连续签到:0 天
[LV.100]试剑无线
发表于 2014-12-19 14:26 来自手机 |显示全部楼层
帮顶,赚个跑包钱。
回复

使用道具 举报

185

回帖

2134

积分

779 小时

在线时间

少校

注册时间
2011-2-12
金币
1825 个
威望
0 个
荣誉
0 个
累计签到:1048 天
连续签到:1 天
[LV.1095]铁杆粉丝
发表于 2014-12-20 16:46 |显示全部楼层
不同款,但是我也等线呢,来了我也要试验一下,
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 注册 微信登录

本版积分规则

Archiver | 手机版 | 无线门户 ( 粤ICP备11076993号|粤公网安备44010602008359号 ) |网站地图

GMT+8, 2025-10-12 05:41

返回顶部 返回列表