三元达500MW无线AP WPB-5000-I-T-GN-27P

信嘉‖通讯

hijk1 发表于 2015-3-25 21:54
可以刷openwrt固件了

亲  您有WPB-5000-I-T-GN-27P   openwrt固件  能发个给我么  540734850@qq.com

wang7268

WPB-5000-I-T-GN-27P   
U-Boot 1.1.4 (May 31 2012 - 19:28:20)

AP91 (ar7240) U-boot
DRAM:  
sri
ar7240_ddr_initial_config(146): python ddr init
#### TAP VALUE 1 = 9, 2 = a
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 262k for U-Boot at: 83fbc000
Reserving 192k for malloc() at: 83f8c000
Reserving 44 Bytes for Board Info at: 83f8bfd4
Reserving 36 Bytes for Global Data at: 83f8bfb0
Reserving 128k for boot params() at: 83f6bfb0
Stack Pointer at: 83f6bf98
Now running in RAM - U-Boot at: 83fbc000
id read 0x100000ff
flash size 16777216, sector count = 256
Flash: 16 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Hit any key to stop autoboot:  2  1  0
read image version 121 size = 0x006fc010
checking crc...
crc ok!
boot_partition : 1
## Booting image at 9f050010 ...
   Image Name:   Linux Kernel Image
   Created:      2013-02-02   8:32:31 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    933212 Bytes = 911.3 kB
   Load Address: 80002000
   Entry Point:  8028d000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8028d000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

Booting AR7240(Python)...
found squashfs at 150010

Starting pid 14, console /dev/ttyS0: '/etc/rc.d/rcS'
Unlocking uboot-env ...
Reading from uboot-env to /var/tmp/bootcfg ...  [ ][r][r]
Install gpio modules
bconf = 00:1F:6F:34:9D:B0
Install wifi modules
wifi1     no private ioctls.

SIOCGIFFLAGS: No such device
SIOCSIFTXQLEN: No such device
wlan0
bconf = 00:1F:6F:34:9D:B0
2.4G Management IP(192.168.10.228) Subnet(255.255.255.0) is old, use new default value!
wlan0
bconf = 00:1F:6F:34:9D:B0
Install wan modules
udhcpc (v0.9.9-pre) started
Jan  1 00:00:07 udhcpc[98]: udhcpc (v0.9.9-pre) started

Sending discover...
Jan  1 00:00:08 udhcpc[98]: Sending discover...


Starting pid 122, console /dev/ttyS0: '/sbin/getty'
WPB-5000 login: Sending discover...

wang7268

怎么进入设置界面

wang7268

扫描的结果  怎么连接

wang7268

SSID    空的

wang7268

用户名 management  密码management    不能连接

逛江湖

这个不好玩啊

疯男国际

空SSID 这么连呢 求助

xqsf

wang7268 发表于 2016-1-6 21:32
WPB-5000-I-T-GN-27P   
U-Boot 1.1.4 (May 31 2012 - 19:28:20)

请问刷的是什么固件？还是只是刷了uboot？

cfigyxy666

欧阳雄风 发表于 2013-4-25 09:14
选择PPPOE上网设置好以后，状态中显示已经连接。
笔记本，台式机需要选择自动获得IP。

这AP可卖多少钱，带独立放大模块那种的

yuyu2627182

15一个 买了3个  无线信号没有想象的那么好 和家用路由器没区别 可能是天线没有匹配好

想刷dd固件了 不知道大神是怎么刷的 Dlink DIR-825 求编程器固件 折腾万岁 谢谢！