ubnt解决方案
查看: 748|回复: 4

AP103有两个镜像,怎么确定启动的是哪个?

[复制链接]

24

回帖

184

积分

41 小时

在线时间

上等兵

注册时间
2022-1-27
金币
152 个
威望
0 个
荣誉
0 个
累计签到:3 天
连续签到:0 天
[LV.20]漫游旅程
发表于 2022-2-4 21:56
APBoot 1.5.2.7 (build 41761)
Built: 2014-01-16 at 01:21:45

Model: AP-103
CPU:   AR9344 revision: 1.2
Clock: 560 MHz, DDR rate: 429 MHz, Bus clock: 214 MHz
DRAM:  128 MB
POST1: passed
Copy:  done
Flash: 32 MB
Power: DC
PCI:   scanning bus 0 ...
       dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3
       00  00  168c  0033 00002   01 10000004 00000000 00000000 00000000
Net:   eth0
Radio: ar9590#0, ar9344#1

Hit <Enter> to stop autoboot:  0
apboot>
apboot>
apboot>
apboot> osinfo
Partition 0:
    image type: 0
  machine type: 26
          size: 10749816
       version: 6.5.4.3-6.5.4.3
  build string: ArubaOS version 6.5.4.3-6.5.4.3 for Pegasus (p4build@lemnos) (gcc version 4.3.3) #61959 Thu Oct 19 21:29:30 PDT 2017
         flags: Instant preserve

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.

Switching to flash bank: 2
Partition 1:
    image type: 0
  machine type: 26
          size: 10749816
       version: 6.5.4.3-6.5.4.3
  build string: ArubaOS version 6.5.4.3-6.5.4.3 for Pegasus (p4build@lemnos) (gcc version 4.3.3) #61959 Thu Oct 19 21:29:30 PDT 2017
         flags: Instant preserve

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
Switching to flash bank: 1
apboot> boot
Checking image @ 0xbf100000 (bank 1)

Image is signed; verifying checksum... passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
ELF file is 32 bit
Loading .text @ 0x81c00000 (10680056 bytes)
Loading .data @ 0x8262f700 (32 bytes)
Clearing .bss @ 0x8262f720 (16 bytes)
## Starting application at 0x81c00000 ...
Uncompressing.......................................................................................................


Aruba Networks
ArubaOS Version 6.5.4.3-6.5.4.3 (build 61959 / label #61959)
Built by p4build@lemnos on 2017-10-19 at 21:29:30 PDT (gcc version 4.3.3)
CPU Rev: 2122
934x CPU
flash_size passed from bootloader = 32
arg 1: mem=128M
Flash variant: 32M
ath_sys_frequency: cpu apb ddr apb cpu 560 ddr 430 ahb 215
Cache parity protection disabled
ath_timer_init: plat time init done
Using 280.000 MHz high precision timer. cycles_per_jiffy=560000
Memory: 115840k/131072k available (1720k kernel code, 15096k reserved, 791k data, 9692k init, 0k highmem)
available.
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=35692032
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com> .................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
PCI init:ath_pcibios_init
Returning IRQ 64
ATH GPIOC major 0
wdt: registered with refresh
Enabling Watchdog
Talisker RSSI LED initialization
Concatenating MTD devices:
(0): "bank1"
(1): "bank2"
into device "flash"
Creating 1 MTD partitions on "flash":
0x00000000-0x02000000 : "flash"
i2c /dev entries driver
i2c-talisker: using default base 0x18040000
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver

Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT
Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT
Starting Kernel DES KAT ...Completed Kernel DES KAT
Starting Kernel AES KAT ...Completed Kernel AES KAT

Starting Kernel AESGCM KAT ...Completed Kernel AESGCM KAT

Thu Jan  1 00:00:00 PST 1970
Domain Name: SetMeUp.arubanetworks.com
Current OEM Name : Aruba Networks
Disabling ipv6 for devices by default
/etc/init.d/rcS: 751: cannot create /proc/sys/net/ipv6/conf/default/disable_ipv6: Directory nonexistent
No panic info available
Backup ENV.
ATHR_GMAC: RX TASKLET - Pkts per Intr:16
ATHR_GMAC: Mac address for unit 0:80d20bc0
ATHR_GMAC: 94:b4:0f:c4:cd:88
ATHR_GMAC: Mac capability flags    :   42201
ATHR_GMAC: RX TASKLET - Pkts per Intr:16
ATHR_GMAC: Mac address for unit 1:80d20bc0
ATHR_GMAC: 94:b4:0f:c4:cd:89
mac:1 Registering S27....
ATHR_GMAC: Mac capability flags    :   42A00
athrs17_reg_init:done
Phy setup Complete
Enter non-FIPS mode
Cfg len is 2607
Starting watchdog process...
Loading configuration file of length 2607...
wifi uplink not present...
extended ssid config detected...
Terminal access enabled...
Valid SSID detected...
touching file /tmp/ip_mode_0
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
ADDRCONF(NETDEV_UP): bond0: link is not ready
Ethernet uplink not active yet
Ethernet uplink not active yet
disable auto topology rules
Starting up in standalone mode

Enet:0 port0 up
athr_gmac_poll_link: unit 0 link change to up
ATH_MAC_TIMER: enet unit:0 is up...
Mii 1000Mbps full duplex
ATH_MAC_TIMER: Done cfg2 0x7235 ifctl 0x0 miictrl
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
extended ssid is activated on the platform ...
copying bootuplodrvlog_mod: module license 'Proprietary' taints kernel.
g ...
AP xml model 76, num_radios 2 (jiffies 21582)
apType 76 hw_opmode 0
radio 0: band 1 ant 0 max_ssid 16
radio 1: band 0 ant 0 max_ssid 16
init_asap_mod: installation:0
election init: rand=17 HZ=500
IAP client match init
set device anul0 mtu to 2000
notify asap_mod 3g no present...
notify asap standalone ap...
apdot1x authentication is not enabled
LLDP not sent yet, DHCP is waiting
LLDP not sent yet, DHCP is waiting
LLDP not sent yet, DHCP is waiting
LLDP not sent yet, DHCP is waiting
LLDP not sent yet, DHCP is waiting
Starting DHCP
Getting an IP address...
Jan  1 00:00:39 udhcpc[1745]: udhcpc (v0.9.9-pre) started
Jan  1 00:00:39 udhcpc[1745]: send_discover: pkt num 0, secs 0
Jan  1 00:00:39 udhcpc[1745]: Sending discover...
Jan  1 00:00:39 udhcpc[1745]: send_selecting: pkt num 0, secs 0
Jan  1 00:00:39 udhcpc[1745]: Sending select for 192.168.137.116...
Jan  1 00:00:39 udhcpc[1745]: Lease of 192.168.137.116 obtained, lease time 604800
ip_time_handler: Got ip and packets on bond0 Started master election 8-0, rand 16
192.168.137.116 255.255.255.0 192.168.137.1
ADP is disabled by uap_controller_less
Compressing all files in the /etc/httpd directory...
Done.
Starting Webserver
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
bind: Transport endpoint is not connected
Launching NTP Client on pool.ntp.org
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_rate_atheros: Aruba Networks Rate Control Algorithm
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_spectrum: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)
Restoring Cal data from Flash
Reading from Addr: 0xbffe5000
ath_attach: scn 84c70280 sc 84e40000 ah 84e80000
wifi0: Base BSSID 94:b4:0f:cc:d8:90, 16 available BSSID(s)
bond0 address=94:b4:0f:c4:cd:88
br0 address=94:b4:0f:c4:cd:88
wifi0: AP type AP-103, radio 0, max_bssids 16
wifi0: Atheros 9580: mem=0x10000000, irq=64 hw_base=0xb0000000
ath_ahb: 0.9.4.5 (Atheros/multi-bss)
ath_ahb: init_ath_wmac
Enterprise mode: 0x00000000
Restoring Cal data from Flash
Reading from Addr: 0xbffe1000
ath_attach: scn 84940280 sc 84960000 ah 84980000
wifi1: Base BSSID 94:b4:0f:cc:d8:80, 16 available BSSID(s)
bond0 address=94:b4:0f:c4:cd:88
br0 address=94:b4:0f:c4:cd:88
wifi1: AP type AP-103, radio 1, max_bssids 16
wifi1: Atheros 9340: mem=0xb8100000, irq=2
shutting down watchdog process (nanny will restart it)...

        <<<<<       Welcome to the Access Point     >>>>>

Completed SW FIPS KAT test
User: i am master now
(11:23:53) !!! Init ---> Master
asap_send_elected_master: sent successfully
turn off mobility
turn off mobility
turn off mobility
turn off mobility
turn off mobility
turn off mobility


1967

回帖

1万

积分

2554 小时

在线时间

上校

30天持久勋章

注册时间
2010-3-23
金币
16016 个
威望
22 个
荣誉
1 个
累计签到:3067 天
连续签到:14 天
[LV.3650]以坛为家
发表于 2022-2-5 06:53
默认启动0

24

回帖

184

积分

41 小时

在线时间

上等兵

注册时间
2022-1-27
金币
152 个
威望
0 个
荣誉
0 个
累计签到:3 天
连续签到:0 天
[LV.20]漫游旅程
发表于 2022-2-5 08:50

什么情况下会启动1,可以人为选择启动哪个吗

1967

回帖

1万

积分

2554 小时

在线时间

上校

30天持久勋章

注册时间
2010-3-23
金币
16016 个
威望
22 个
荣誉
1 个
累计签到:3067 天
连续签到:14 天
[LV.3650]以坛为家
发表于 2022-2-6 06:50
可以人为选择启动

24

回帖

184

积分

41 小时

在线时间

上等兵

注册时间
2022-1-27
金币
152 个
威望
0 个
荣誉
0 个
累计签到:3 天
连续签到:0 天
[LV.20]漫游旅程
发表于 2022-2-6 18:26
hijk1 发表于 2022-2-6 06:50
可以人为选择启动

你好,AP103 每次断电后就admin登录不了,所有的配置也都没了,知道是什么问题吗?或者这是AP在没有AC下的正常情况?

站点统计 | Archiver | 手机版 | 无线门户 ( 粤ICP备11076993号|粤公网安备44010602008359号 ) |网站地图

GMT+8, 2024-4-25 21:02

返回顶部 返回列表