ubnt解决方案
查看: 187|回复: 0

[求助] 请问大哥们TFTP怎么刷不进去固件?

[复制链接]

1003

帖子

9563

积分

533 小时

在线时间

中校

Rank: 6Rank: 6

注册时间
2009-7-19
金币
8465 个
威望
8 个
荣誉
0 个
  • TA的每日心情
    难过
    2021-10-5 12:32
  • 已绑定手机
    发表于 2021-12-7 20:13 |显示全部楼层
    Anywlan微信公众号
    路由器LAN正常能连接上就是无法上传上去!出现下面代码
    Ralink UBoot Version: 3.5.2.0
    --------------------------------------------
    ASIC 3883_MP (MAC to RTL Mode)
    DRAM component: 512 Mbits DDR, width 16
    DRAM bus: 32 bit
    Total memory: 128 MBytes
    Flash component: NOR Flash
    Date:Apr 22 2012  Time:07:28:09
    ============================================
    icache: sets:512, ways:4, linesz:32 ,total:65536
    dcache: sets:256, ways:4, linesz:32 ,total:32768


    ##### The CPU freq = 500 MHZ ####


    SDRAM bus set to 32 bit
    estimate memory size =128 Mbytes


    RTL giga Mac support


    GPIO pin 24 reset to switch
    rtk8367RB_init...... OK!


    Please choose the operation:
       1: Load system code to SDRAM via TFTP.
       2: Load system code then write to Flash via TFTP.
       3: Boot system code via Flash (default).
       4: Entr boot command line interface.
       7: Load Boot Loader code then write to Flash via Serial.
       9: Load Boot Loader code then write to Flash via TFTP.


    You choosed 2
                                                                                  0




    2: System Load Linux Kernel then write to Flash via TFTP.
    Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
    Please Input new ones /or Ctrl-C to discard
            Input device IP (10.10.10.123) ==:10.10.10.123
            Input server IP (10.10.10.3) ==:10.10.10.3
            Input Linux Kernel filename () ==:root_ulmage


    netboot_common, argc= 3


    NetTxPacket = 0x87FE3680


    KSEG1ADDR(NetTxPacket) = 0xA7FE3680


    NetLoop,call eth_halt !


    NetLoop,call eth_init !
    Trying Eth0 (10/100-M)


    Waitting for RX_DMA_BUSY status Start... done




    RTL giga Mac support


    GPIO pin 24 reset to switch
    rtk8367RB_init...... OK!


    Header Payload scatter function is Disable !!


    ETH_STATE_ACTIVE!!
    Using Eth0 (10/100-M) device
    TFTP from server 10.10.10.3; our IP address is 10.10.10.123
    Filename 'root_ulmage'.


    TIMEOUT_COUNT=10,Load address: 0x80100000
    Loading: T



















    您需要登录后才可以回帖 登录 | 注册

    本版积分规则

    QQ | Archiver | 手机版 | 无线论坛 ( 粤ICP备11076993|粤公网安备44010602008359号 ) |网站地图

    GMT+8, 2022-5-25 21:56

    返回顶部 返回列表