新兵上阵
- 注册时间
- 2019-8-23
- 金币
- 65 个
- 威望
- 1 个
- 荣誉
- 0 个
累计签到:4 天 连续签到:0 天 [LV.20]漫游旅程
|
发表于 2019-8-23 22:42
手上有个K2T 似乎是出厂就是砖,通电无wifi信号,lan无法获取ip。当时嫌麻烦没有售后就压箱底了。最近没事翻出来ttl刷机尝试修复下。所有步骤按照网上攻略操作,无任何问题。但是刷好后故障依旧,这就搞不懂了。有大神帮忙看看是啥问题?顺便把ttl显示的代码贴上。
▒▒h> reset
U-Boot 1.1.4-gbc73b198 (Mar 29 2018 - 15:36:58)
ap152 - Dragonfly 1.0DRAM:
sri
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0xf, 0xf, 0xf, 0xf)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 202k for U-Boot at: 83fcc000
Reserving 192k for malloc() at: 83f9c000
Reserving 44 Bytes for Board Info at: 83f9bfd4
Reserving 36 Bytes for Global Data at: 83f9bfb0
Reserving 128k for boot params() at: 83f7bfb0
Stack Pointer at: 83f7bf98
Now running in RAM - U-Boot at: 83fcc000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x4b962100
Hit any key to stop autoboot: 0
## Booting image at 9f090000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2018-04-28 10:22:54 UTC
Image Type: MIPS Linux Multi-File Image (lzma compressed)
Data Size: 1046847 Bytes = 1022.3 kB
Load Address: 80060000
Entry Point: 80060000
Contents:
Image 0: 1046839 Bytes = 1022.3 kB
Verifying Checksum at 0x9f090040 ...OK
Uncompressing Multi-File Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (xianjie.yang@server-ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Apr 28 18:22:42 CST 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=AP152 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,64k(config),320k(permanent),1152k(kernel),14592k(rootfs),64k(art),15744k@0x90000(firmware) rootfstype=squashfs,jffs2 noinitrd crashkernel=10M@20M oops=panic
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61448k/65536k available (2227k kernel code, 4088k reserved, 544k data, 180k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.060000] Performance counters: mips/74K PMU enabled, 4 32-bit counters available to each CPU, irq 13
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.080000] MIPS: machine is Qualcomm Atheros AP152 reference board
[ 0.090000]
[ 0.090000] WLAN firmware dump buffer allocation of 2097152 bytes @ address 0x83a00000- SUCCESS !!!
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.310000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0001]
[ 0.320000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.330000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.330000] Switching to clocksource MIPS
[ 0.340000] NET: Registered protocol family 2
[ 0.340000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.350000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.350000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.360000] TCP reno registered
[ 0.360000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.370000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.370000] NET: Registered protocol family 1
[ 0.390000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.390000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.400000] msgmni has been set to 120
[ 0.410000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.420000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.440000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.450000] console [ttyS0] enabled, bootconsole disabled
[ 0.450000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] m25p80 spi0.0: found gd25q128, expected m25p80
[ 0.470000] m25p80 spi0.0: gd25q128 (16384 Kbytes)
[ 0.470000] 7 cmdlinepart partitions found on MTD device spi0.0
[ 0.480000] Creating 7 MTD partitions on "spi0.0":
[ 0.490000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.490000] 0x000000030000-0x000000040000 : "config"
[ 0.500000] 0x000000040000-0x000000090000 : "permanent"
[ 0.500000] 0x000000090000-0x0000001b0000 : "kernel"
[ 0.510000] 0x0000001b0000-0x000000ff0000 : "rootfs"
[ 0.520000] mtd: partition "rootfs" set to be root filesystem
[ 0.520000] mtd: partition "rootfs_data" created automatically, ofs=900000, len=200000
[ 0.530000] 0x000000900000-0x000000b00000 : "rootfs_data"
[ 0.540000] 0x000000ff0000-0x000001000000 : "art"
[ 0.540000] 0x000000090000-0x000000ff0000 : "firmware"
[ 0.550000] m25p80 spi0.1: found pm25lv512, expected m25p80
[ 0.560000] m25p80 spi0.1: pm25lv512 (64 Kbytes)
[ 0.700000] ag71xx_mdio: probed
[ 0.700000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.280000] eth0: Atheros AR8327 switch driver attached.
[ 4.210000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 4.220000] init_module:price_compare!
[ 4.230000] creat nlsock ok!
[ 4.230000] TCP cubic registered
[ 4.230000] NET: Registered protocol family 17
[ 4.240000] Bridge firewalling registered
[ 4.240000] 8021q: 802.1Q VLAN Support v1.8
[ 4.250000] ### of_selftest(): No testcase data in device tree; not running tests
[ 4.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 4.270000] Freeing unused kernel memory: 180k freed
- preinit -
[ 9.270000] eth0: link up (1000Mbps/Full duplex)
- fac_mode=y -
- failsafe -
BusyBox v1.19.4 (2018-04-28 17:44:20 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
MM NM MMMMMMM M M
$MMMMM MMMMM MMMMMMMMMMM MMM MMM
MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM
MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM'
MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM
MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM
MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM
MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM
MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM
MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM
MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM
MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM
MMMMMM MMMMN M MMMMMMMMM MMMM MMMM
MMMM M MMMMMMM M M
M
---------------------------------------------------------------
For those about to rock... (QCA9558.LN, unknown)
---------------------------------------------------------------
root@(none):/# ▒▒h> reset
root@(none):/#
root@(none):/# U-Boot 1.1.4-gbc73b198 (Mar 29 2018 - 15:36:58)
root@(none):/#
root@(none):/# ap152 - Dragonfly 1.0DRAM:
root@(none):/# sri
root@(none):/# ath_ddr_initial_config(278): (ddr2 init)
root@(none):/# ath_sys_frequency: cpu 775 ddr 650 ahb 258
root@(none):/# Tap values = (0xf, 0xf, 0xf, 0xf)
root@(none):/# 64 MB
root@(none):/# Top of RAM usable for U-Boot at: 84000000
root@(none):/# Reserving 202k for U-Boot at: 83fcc000
root@(none):/# Reserving 192k for malloc() at: 83f9c000
root@(none):/# Reserving 44 Bytes for Board Info at: 83f9bfd4
root@(none):/# Reserving 36 Bytes for Global Data at: 83f9bfb0
root@(none):/# Reserving 128k for boot params() at: 83f7bfb0
root@(none):/# Stack Pointer at: 83f7bf98
root@(none):/# Now running in RAM - U-Boot at: 83fcc000
root@(none):/# Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x18
root@(none):/# flash size 16MB, sector count = 256
root@(none):/# Flash: 16 MB
root@(none):/# *** Warning - bad CRC, using default environment
root@(none):/#
proot@(none):/# Power up PLL with outdiv = 0 then switch to 3
root@(none):/# In: serial
root@(none):/# Out: serial
root@(none):/# Err: serial
root@(none):/# Net: ath_gmac_enet_initialize...
root@(none):/# No valid address in Flash. Using fixed address
root@(none):/# ath_gmac_enet_initialize: reset mask:c02200
root@(none):/# athr_mgmt_init ::done
aroot@(none):/# Dragonfly ----> S17 PHY *
root@(none):/# athrs17_reg_init: complete
root@(none):/# SGMII in forced mode
root@(none):/# athr_gmac_sgmii_setup SGMII done
root@(none):/# : cfg1 0x80000000 cfg2 0x7114
root@(none):/# eth0: 00:03:7f:09:0b:ad
root@(none):/# eth0 up
root@(none):/# eth0
root@(none):/# Setting 0x181162c0 to 0x4b962100
root@(none):/# Hit any key to stop autoboot: 0
root@(none):/# ## Booting image at 9f090000 ...
root@(none):/# Image Name: MIPS OpenWrt Linux-3.3.8
root@(none):/# Created: 2018-04-28 10:22:54 UTC
root@(none):/# Image Type: MIPS Linux Multi-File Image (lzma compressed)
root@(none):/# Data Size: 1046847 Bytes = 1022.3 kB
root@(none):/# Load Address: 80060000
root@(none):/# Entry Point: 80060000
root@(none):/# Contents:
root@(none):/# Image 0: 1046839 Bytes = 1022.3 kB
root@(none):/# Verifying Checksum at 0x9f090040 ...OK
root@(none):/# Uncompressing Multi-File Image ... OK
root@(none):/# No initrd
root@(none):/# ## Transferring control to Linux (at address 80060000) ...
root@(none):/# ## Giving linux memsize in bytes, 67108864
root@(none):/#
root@(none):/# Starting kernel ...
root@(none):/#
root@(none):/# [ 0.000000] Linux version 3.3.8 (xianjie.yang@server-ubuntu) (
gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Apr 28
18:22:42 CST 2018
root@(none):/# [ 0.000000] bootconsole [early0] enabled
root@(none):/# [ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
root@(none):/# [ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0
root@(none):/# [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.33
3MHz, Ref:25.000MHz
root@(none):/# [ 0.000000] Determined physical RAM map:
root@(none):/# [ 0.000000] memory: 04000000 @ 00000000 (usable)
root@(none):/# [ 0.000000] Initrd not found or empty - disabling initrd
root@(none):/# [ 0.000000] Zone PFN ranges:
root@(none):/# [ 0.000000] Normal 0x00000000 -> 0x00004000
root@(none):/# [ 0.000000] Movable zone start PFN for each node
root@(none):/# [ 0.000000] Early memory PFN ranges
root@(none):/# [ 0.000000] 0: 0x00000000 -> 0x00004000
root@(none):/# [ 0.000000] Built 1 zonelists in Zone order, mobility grouping
on. Total pages: 16256
root@(none):/# [ 0.000000] Kernel command line: board=AP152 console=ttyS0,11
5200 mtdparts=spi0.0:192k(u-boot)ro,64k(config),320k(permanent),1152k(kernel),14
592k(rootfs),64k(art),15744k@0x90000(firmware) rootfstype=squashfs,jffs2 noinitr
d crashkernel=10M@20M oops=panic
root@(none):/# [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes
)
root@(none):/# [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 3
2768 bytes)
root@(none):/# [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16
384 bytes)
root@(none):/# [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, lines
ize 32 bytes.
root@(none):/# [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliase
s, linesize 32 bytes
root@(none):/# [ 0.000000] Writing ErrCtl register=00000000
[root@(none):/# [ 0.000000] Readback ErrCtl register=00000000
root@(none):/# [ 0.000000] Memory: 61448k/65536k available (2227k kernel code
, 4088k reserved, 544k data, 180k init, 0k highmem)
root@(none):/# [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObject
s=0, CPUs=1, Nodes=1
root@(none):/# [ 0.000000] NR_IRQS:83
root@(none):/# [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=192
9216)
root@(none):/# [ 0.060000] pid_max: default: 32768 minimum: 301
root@(none):/# [ 0.060000] Mount-cache hash table entries: 512
root@(none):/# [ 0.060000] Performance counters: mips/74K PMU enabled, 4 32-b
it counters available to each CPU, irq 13
root@(none):/# [ 0.070000] NET: Registered protocol family 16
root@(none):/# [ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device:
ath79
root@(none):/# [ 0.080000] MIPS: machine is Qualcomm Atheros AP152 reference
board
0root@(none):/# [ 0.090000]
root@(none):/# [ 0.090000] WLAN firmware dump buffer allocation of 2097152 by
tes @ address 0x83a00000- SUCCESS !!!
root@(none):/# [ 0.100000] registering PCI controller with io_map_base unset
root@(none):/# [ 0.310000] bio: create slab <bio-0> at 0
root@(none):/# [ 0.310000] PCI host bridge to bus 0000:00
root@(none):/# [ 0.310000] pci_bus 0000:00: root bus resource [mem 0x12000000
-0x13ffffff]
root@(none):/# [ 0.320000] pci_bus 0000:00: root bus resource [io 0x0001]
root@(none):/# [ 0.320000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-
0x121fffff 64bit]
0.33000root@(none):/# [ 0.330000] pci 0000:00:00.0: using irq 40 for pin 1
root@(none):/# [ 0.330000] Switching to clocksource MIPS
root@(none):/# [ 0.340000] NET: Registered protocol family 2
root@(none):/# [ 0.340000] IP route cache hash table entries: 1024 (order: 0,
4096 bytes)
.root@(none):/# [ 0.340000] TCP established hash table entries: 2048 (order: 2
, 16384 bytes)
root@(none):/# [ 0.350000] TCP bind hash table entries: 2048 (order: 1, 8192
bytes)
root@(none):/# [ 0.350000] TCP: Hash tables configured (established 2048 bind
2048)
root@(none):/# [ 0.360000] TCP reno registered
root@(none):/# [ 0.360000] UDP hash table entries: 256 (order: 0, 4096 bytes)
root@(none):/# [ 0.370000] UDP-Lite hash table entries: 256 (order: 0, 4096 b
ytes)
root@(none):/# [ 0.370000] NET: Registered protocol family 1
root@(none):/# [ 0.390000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
root@(none):/# [ 0.390000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
root@(none):/# [ 0.400000] msgmni has been set to 120
root@(none):/# [ 0.410000] io scheduler noop registered
root@(none):/# [ 0.410000] io scheduler deadline registered (default)
root@(none):/# [ 0.420000] Serial: 8250/16550 driver, 1 ports, IRQ sharing di
sabled
root@(none):/# [ 0.440000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11)
is a 16550A
root@(none):/# [ 0.450000] console [ttyS0] enabled, bootconsole disabled
root@(none):/# [ 0.450000] console [ttyS0] enabled, bootconsole disabled
root@(none):/# [ 0.460000] m25p80 spi0.0: found gd25q128, expected m25p80
root@(none):/# [ 0.470000] m25p80 spi0.0: gd25q128 (16384 Kbytes)
4root@(none):/# [ 0.470000] 7 cmdlinepart partitions found on MTD device spi0.
0
.root@(none):/# [ 0.480000] Creating 7 MTD partitions on "spi0.0":
root@(none):/# [ 0.490000] 0x000000000000-0x000000030000 : "u-boot"
root@(none):/# [ 0.490000] 0x000000030000-0x000000040000 : "config"
0root@(none):/# [ 0.500000] 0x000000040000-0x000000090000 : "permanent"
root@(none):/# [ 0.500000] 0x000000090000-0x0000001b0000 : "kernel"
0root@(none):/# [ 0.510000] 0x0000001b0000-0x000000ff0000 : "rootfs"
root@(none):/# [ 0.520000] mtd: partition "rootfs" set to be root filesystem
root@(none):/# [ 0.520000] mtd: partition "rootfs_data" created automatically
, ofs=900000, len=200000
root@(none):/# [ 0.530000] 0x000000900000-0x000000b00000 : "rootfs_data"
root@(none):/# [ 0.540000] 0x000000ff0000-0x000001000000 : "art"
root@(none):/# [ 0.540000] 0x000000090000-0x000000ff0000 : "firmware"
root@(none):/# [ 0.550000] m25p80 spi0.1: found pm25lv512, expected m25p80
root@(none):/# [ 0.560000] m25p80 spi0.1: pm25lv512 (64 Kbytes)
root@(none):/# [ 0.700000] ag71xx_mdio: probed
root@(none):/# [ 0.700000] eth0: Atheros AG71xx at 0xb9000000, irq 4
root@(none):/# [ 1.280000] eth0: Atheros AR8327 switch driver attached.
root@(none):/# [ 4.210000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-
mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
root@(none):/# [ 4.220000] init_module:price_compare!
root@(none):/# [ 4.230000] creat nlsock ok!
root@(none):/# [ 4.230000] TCP cubic registered
root@(none):/# [ 4.230000] NET: Registered protocol family 17
2root@(none):/# [ 4.240000] Bridge firewalling registered
root@(none):/# [ 4.240000] 8021q: 802.1Q VLAN Support v1.8
root@(none):/# [ 4.250000] ### of_selftest(): No testcase data in device tree
; not running tests
root@(none):/# [ 4.260000] VFS: Mounted root (squashfs filesystem) readonly o
n device 31:4.
root@(none):/# [ 4.270000] Freeing unused kernel memory: 180k freed
iroot@(none):/# - preinit -
root@(none):/# [ 9.270000] eth0: link up (1000Mbps/Full duplex)
root@(none):/# - fac_mode=y -
root@(none):/# - failsafe -
root@(none):/#
root@(none):/#
root@(none):/# BusyBox v1.19.4 (2018-04-28 17:44:20 CST) built-in shell (ash)
root@(none):/# Enter 'help' for a list of built-in commands.
root@(none):/#
root@(none):/# MM NM MMMMMMM M
M
root@(none):/# $MMMMM MMMMM MMMMMMMMMMM MMM MM
M
root@(none):/# MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMM
M
root@(none):/# MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM
'
> MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM
> MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM
> MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM
> MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM
> MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM
> MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM
> MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM
> MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM
> MMMMMM MMMMN M MMMMMMMMM MMMM MMMM
> MMMM M MMMMMMM M M
> M
> ---------------------------------------------------------------
> For those about to rock... (QCA9558.LN, unknown)
> ---------------------------------------------------------------
> root@(none):/#
>
|
|