求助 d-link dir-825b1 硬改网件3700 刷v2版DD固件挂了

二维

求助 d-link dir-825b1 硬改网件3700  刷v2版DD固件挂了，听说TTL刷机能救回来，可是怎么也搞不定，求大神指导，十分感谢！

4 u- l! U8 H5 C4 ~U-Boot 1.1.4DNI1.6 (May 22 2009 - 16:37:44)

. C6 h% J# \  \* m% Q2 H# R9 K5 dWNDR3700U (ar7100) U-boot 0.0.12
# [; `% F  F, PDRAM:  b8050000: 0xc0140180
9 @. O3 G8 M9 O, ^' C  O$ g8 g128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 315k for U-Boot at: 87fb0000
, `& Z% q8 M' t$ C& SReserving 192k for malloc() at: 87f80000
Reserving 44 Bytes for Board Info at: 87f7ffd4
$ b, y5 w  a# E8 {Reserving 36 Bytes for Global Data at: 87f7ffb0
Reserving 128k for boot params() at: 87f5ffb0
Stack Pointer at: 87f5ff98
9 i- X" w$ `  S7 t& vNow running in RAM - U-Boot at: 87fb0000
id read 0x100000ff
9 n% T' Z4 E" r: A# U. m8 }# s( d3 a' cflash size 8MB, sector count = 128
Flash:  8 MB
*** Warning - bad CRC, using default environment
& r. {! X( e& o! ~
  O( E1 Q0 I$ C& Q9 n$ d. ~In:    serial
Out:   serial
Err:   serial
4 _/ R4 T$ `  [$ Y  NNet:   ag7100_enet_initialize...
CHH:mac: 0 if: 2
CHH:mac:verify: 0 if: 00000002
- k  p0 P! }; J5 \3 B: cfg1 0xf cfg2 0x7014
' P$ a# G" O) J; a4 \* x6 eeth0: 00:24:01:de:d9:65
/ u& n# u1 \/ \eth0 up
CHH:mac: 1 if: 1
CHH:mac:verify: 1 if: 00000001
* \( }7 ?/ s* O0 c& m+ q0 v: cfg1 0xf cfg2 0x7014
) w# ]- y3 a( O2 v  feth1: 00:24:01:de:d9:66
3 M( _: q( u9 f% g& B% F" n  U6 m' e& ueth1 up
" a% E/ a0 R! q) [" {6 d+ ]eth0, eth1
Trying eth0
7 s! T% s( T3 S& i: unit 0 phy is up...RGMii 1000Mbps full duplex
: U# I2 E. I* o+ W! i( |#259:ag7100_set_mac_from_link
: pll reg 0x18050010: 0x11110000  
! @& l; @" i. P: cfg_1: 0x1ff0000
: cfg_2: 0x3ff
: cfg_3: 0x8001ff
: cfg_4: 0xffff
- H2 D7 t: U! A9 m- J: cfg_5: 0xfffef
0 h8 {' E$ C$ S1 \2 y8 T1 K+ z; M: done cfg2 0x7215 ifctl 0x40605060 miictrl 0x22

Client starts...[Listening] for ADVERTISE...checksum bad
checksum bad
Tchecksum bad
Tchecksum bad
/ t- W+ g- i% G: d) M: fchecksum bad
* D; H; b" }5 n) `Tchecksum bad
1 Z' O2 i0 b: O: `' Z4 R
Retry count exceeded; boot the image as usual
, ]/ R# Y! y$ ?6 z, z4 E
* {+ _! r. }4 ?+ [. w/ e; S nmrp server is stopped or failed !
Hit any key to stop autoboot:  0
   Bad Magic Number
4 [5 ]9 o" o, ]1 L7 bTrying eth0
: unit 0 phy is up...RGMii 1000Mbps full duplex
#259:ag7100_set_mac_from_link
+ N' u+ C& |7 o: pll reg 0x18050010: 0x11110000  
: cfg_1: 0x1ff0000
: cfg_2: 0x3ff
: cfg_3: 0x8001ff
3 @' s1 u3 L8 Q4 Z: cfg_4: 0xffff
% U8 a. [* z  X2 C: ?( @/ l: cfg_5: 0xfffef
: done cfg2 0x7215 ifctl 0x40605060 miictrl 0x22
0 C' z8 k) g$ F; H3 P
) E1 h% e; f& {$ z) k/ o2 oThe Router is in TFTP Server Firmware Recovery mode NOW!
% b/ r% v, b7 o; ~: m& K' }& UListening on Port : 69, IP Address: 192.168.1.1...
4 N# Q( J5 Y5 b7 kchecksum bad
* A) U  |! D! C2 b5 C$ O# t- f) Wchecksum bad
Upgrade Mode
- @8 E+ A0 }$ }4 z3 r$ j& x
" b: S4 A% C- N1 m1 q: S" j$ n% }-------------------------------------------------------------------
tpl
3 \7 d% F. a5 T4 K& {: usetenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
' s* E* }& K- z8 B9 iprintenv
tftpboot 0×80000000 u-boot-ar7161-wndr3800.bin
erase 0x9f000000 +0x50000
; O' L( R. R8 s6 D$ `  Qcp.b 0×80000000 0x9f000000 0x50000
bootm 0x9f000000
5 {+ ], ~9 e: h4 T# a使用以上命令好像显示地址0x9f000000不在flash中，erase失败
% q6 b! G1 U: G: D" `另外问一下，dir825改3700刷3800的不死uboot是不是不行呀？网上没找到3700的不死uboot