查看: 1559|回复: 6

[路由改装] 烽火AP2400硬改WAN后识别不到的原因?

203 回帖	498 积分	111 小时在线时间

少尉

注册时间: 2009-4-21

金币: 260 个

威望: 0 个

荣誉: 0 个

发消息

尚未签到

发表于 2016-5-30 07:48 |显示全部楼层

本帖最后由 jasonwang 于 2016-5-30 08:03 编辑

机器是烽火AP2400-20AN, AR7161主控, 交换机AR8316, 国外机原型是JA76PF2, 国外机型有WAN口, 国内机没WAN口, 现人工增加了网变,电阻,电容, 开机瞬间网口灯都复位亮一下, 现故障情况:
1. LAN灯显示正常
2. WAN口插线,物理灯都不亮,电脑上提示未插网线

现在不知道是硬改的不对,还是固件刷的不对, 希望各位大神们给指点下

TTL截取的信息如下:
[ 1.460000] ar8316: Using port 4 as switch port
[ 1.490000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[ 1.500000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII（LAN？）
[ 1.830000] ar8316: Using port 4 as PHY
[ 2.870000] ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[ 2.880000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII（WAN？）

root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet  HWaddr 00:26:7A:20:4D:A7
      inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
      inet6 addr: fe80::226:7aff:fe20:4da7/64 Scopeink
      inet6 addr: fd26:f41c:6526::1/60 Scope:Global
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
      RX packets:207 errors:0 dropped:0 overruns:0 frame:0
      TX packets:58 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:16914 (16.5 KiB)  TX bytes:5464 (5.3 KiB)

eth0    Link encap:Ethernet  HWaddr 00:26:7A:20:4D:A7
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:179 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:0 (0.0 B)  TX bytes:16722 (16.3 KiB)
      Interrupt:4

eth1    Link encap:Ethernet  HWaddr 00:26:7A:20:4D:A8
      UP BROADCAST MULTICAST  MTU:1500  Metric:1
      RX packets:251 errors:0 dropped:0 overruns:0 frame:0
      TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:34953 (34.1 KiB)  TX bytes:3034 (2.9 KiB)
      Interrupt:5 （这里有WAN啊，LUCI界面中只有一个ETH0）

lo       Link encapocal Loopback
      inet addr:127.0.0.1  Mask:255.0.0.0
      inet6 addr: ::1/128 Scope:Host
      UP LOOPBACK RUNNING  MTU:65536  Metric:1
      RX packets:432 errors:0 dropped:0 overruns:0 frame:0
      TX packets:432 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:29376 (28.6 KiB)  TX bytes:29376 (28.6 KiB)

root@OpenWrt:/# [  368.520000] eth1: link up (100Mbps/Full duplex)
[  368.520000] br-lan: port 2(eth1) entered forwarding state
[  368.530000] br-lan: port 2(eth1) entered forwarding state
[  370.530000] br-lan: port 2(eth1) entered forwarding state
[  550.000000] br-lan: port 2(eth1) entered disabled state
[  550.000000] br-lan: port 1(eth0) entered disabled state
[  550.120000] device eth0 left promiscuous mode
[  550.120000] br-lan: port 1(eth0) entered disabled state
[  550.160000] eth0: link down
[  550.160000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  550.190000] device eth1 left promiscuous mode
[  550.190000] br-lan: port 2(eth1) entered disabled state
[  550.220000] eth1: link down
[  550.220000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[  550.250000] device eth0 entered promiscuous mode
[  550.290000] device eth1 entered promiscuous mode
[  550.290000] br-lan: port 2(eth1) entered forwarding state
[  550.300000] br-lan: port 2(eth1) entered forwarding state
[  550.300000] br-lan: port 1(eth0) entered forwarding state
[  550.310000] br-lan: port 1(eth0) entered forwarding state
[  550.540000] eth1: link up (100Mbps/Full duplex)  开机复位吧？
[  551.010000] br-lan: port 1(eth0) entered disabled state
[  551.440000] eth0: link up (1000Mbps/Full duplex) 开机复位吧？
[  551.440000] br-lan: port 1(eth0) entered forwarding state
[  551.450000] br-lan: port 1(eth0) entered forwarding state
[  552.300000] br-lan: port 2(eth1) entered forwarding state
[  553.450000] br-lan: port 1(eth0) entered forwarding state
[  633.010000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  633.020000] device wlan0 entered promiscuous mode
[  633.040000] br-lan: port 3(wlan0) entered forwarding state
[  633.050000] br-lan: port 3(wlan0) entered forwarding state
[  633.050000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  635.050000] br-lan: port 3(wlan0) entered forwarding state
[  724.940000] device wlan0 left promiscuous mode
[  724.940000] br-lan: port 3(wlan0) entered disabled state
[  725.820000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[  725.880000] device wlan0-1 entered promiscuous mode
[  725.880000] br-lan: port 3(wlan0-1) entered forwarding state
[  725.890000] br-lan: port 3(wlan0-1) entered forwarding state
[  725.950000] br-lan: port 3(wlan0-1) entered disabled state
[  726.260000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  729.640000] wlan0: authenticate with a8:57:4e:83:a6:b8
[  729.660000] wlan0: send auth to a8:57:4e:83:a6:b8 (try 1/3)
[  729.670000] wlan0: authenticated
[  729.680000] wlan0: associate with a8:57:4e:83:a6:b8 (try 1/3)
[  729.690000] wlan0: RX AssocResp from a8:57:4e:83:a6:b8 (capab=0x431 status=0 aid=2)
[  729.700000] wlan0: associated
[  729.700000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  729.720000] br-lan: port 3(wlan0-1) entered forwarding state
[  729.730000] br-lan: port 3(wlan0-1) entered forwarding state
[  729.730000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[  731.730000] br-lan: port 3(wlan0-1) entered forwarding state