刷superwrt

Free_like_a_bir

TP886n相信现在市场保有量很大，对于450m路由，2+16确实有些汗颜，白瞎这牛b闪闪的9343u了。
前阶段看到H大【首发】TP9343 路由有救了 全国首发测试版固件http://www.right.com.cn/forum/thread-154116-1-1.html
需要换8闪。这个门槛绊倒很多人吧。
今天看到【SuperWRT】从此2M Flash的设备有救了，已有wr886n（多拨）版本
http://www.anywlan.com/thread-380607-1-1.html
于是好奇，回家把吃灰的886扒衣服，TTL，搞之，进界面顺畅，轻系统。
教程再此 不多说http://superwrt.com/download/test/#installation
说下注意事项，
1.严格按照说明，IP地址必须为192.168.1.10，否则tftp加载不到。
2.下载来的uboot文件名与说明的命令不一样，需要改名uboot_superwrt_tl_wr886n_v5.img 。3.uboot自动获取ip，进web192.168.17.1
没了。。来几个截图，附TTL输出

WLAN IOCTL AP_WMM_NOACK==0=0=1052

WLAN IOCTL AP_CYPHER_2==CCMP=CCMP=1000

WLAN IOCTL AP_NO_EDGE_CH==0=0=1056

WLAN IOCTL AP_MCASTRATE==0=0=1018

WLAN IOCTL AP_MACFILTER_MODE==0=0=1038

WLAN IOCTL AP_MACFILTER_LIST====1000

WLAN IOCTL AP_SHORT_GI=1=1=1=1055

WLAN IOCTL AP_CWMENABLE==1=1=1008

WLAN IOCTL AP_DISABLECOEXT=1=0=1=1075

WLAN IOCTL AP_MCASTENHANCE==2=2=1083

WLAN IOCTL AP_ME_LENGTH==32=32=1085

WLAN IOCTL AP_METIMER==3000=3000=1086

WLAN IOCTL AP_METIMEOUT==12000=12000=1087

WLAN IOCTL AP_MEDROPMCAST==0=0=1089

WLAN IOCTL AP_SSID=liuxuyang=AP136_VxWorks_TPLINK_20130802=liuxuyang=1001
AP_CHMODE=11NGHT40
AP_CWMMODE=1
AP_AMPDU=1
AP_AMPDU_LIMIT=50000
AP_AMPDU_SUBFRAMES=32
AP_PURE_N=0
AP_TX_CHAINMASK=7
AP_RX_CHAINMASK=7
AP_ATHDEBUG=0x00000000
AP_HALDEBUG=0x00000000
>>> WDS 1 ,IEEE80211IOCTL_WDS=61, vapid=0
>>> EXTAP 0 ,IEEE80211IOCTL_SETEXTAP=77, vapid=0
AP_SECMODE=WPA2
WPS_ENABLE=0
Security Mode: WPA2

WLAN IOCTL AP_HIDE_SSID=0=0=0=1005
AP_MACFILTER_MODE=0
WPS_ENABLE=0

WLAN IOCTL AP_BASICRATES==0=0=1039

WLAN IOCTL AP_DEBUG=0=0x00000008=0=1062

WLAN IOCTL AP_TX11NRATE==0x0=0x0=1041

WLAN IOCTL AP_TX11NRETRIES==0x04040404=0x04040404=1078
Starting Hostapd
AP_SSID=liuxuyang
AP_SSID=liuxuyang
AP_HOSTAPD_DEBUG=0
AP_IPADDR=192.168.1.1
AP_SECMODE=WPA2
WPS_ENABLE=0
AP_SECMODE=WPA2
PSK_KEY=lxy09525.con
AP_CYPHER=CCMP
AP_WPA_GROUP_REKEY=86400
AP_WPA_STRICT_REKEY=1
AP_TPSCALE=0
Adding ath0 in bridge ...
tpl

U-Boot 1.1.4 (Jul  4 2014 - 11:09:38)

cus249 - Dragonfly 1.0

DRAM:  16 MB
Top of RAM usable for U-Boot at: 81000000
Reserving 130k for U-Boot at: 80fdc000
Reserving 132k for malloc() at: 80fbb000
Reserving 44 Bytes for Board Info at: 80fbafd4
Reserving 36 Bytes for Global Data at: 80fbafb0
Reserving 128k for boot params() at: 80f9afb0
Stack Pointer at: 80f9af98
Now running in RAM - U-Boot at: 80fdc000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 4MB, sector count = 1024
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Dragonfly----> S27 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x5bb62100
Autobooting in 1 seconds
ath> tftp 0x80060000 uboot_superwrt_tl_wr886n_v5.img
Trying eth1
enet1 port3 up
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename 'uboot_superwrt_tl_wr886n_v5.img'.
Load address: 0x80060000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Trying eth0
eth0 link down
FAIL
Trying eth1
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename 'uboot_superwrt_tl_wr886n_v5.img'.
Load address: 0x80060000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Trying eth0
eth0 link down
FAIL
Trying eth1
ath> tftp 0x80060000 uboot_superwrt_tl_wr886n_v5.img
Trying eth1
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename 'uboot_superwrt_tl_wr886n_v5.img'.
Load address: 0x80060000
Loading: T T T T T T T T ##############
done
Bytes transferred = 68450 (10b62 hex)
ath> erase 0x9f000000 +0x20000
Erasing flash...
First 0x0 last 0x1f sector size 0x1000
=====>erase sector 64k 0x00000000
=====>erase sector 64k 0x00010000

Erased 32 sectors
ath> cp.b 0x80060000 0x9f000000 0x1c000
Copy to Flash... write addr: 9f000000
done
ath> reset

U-Boot 1.1.4-g49d3d3a1-dirty (Dec  4 2015 - 12:58:31)

tl-wr886n-v5 - Dragonfly 1.0

DRAM:  16 MB
Flash:  2 MB (c84015)
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   Dragonfly----> S27 PHY *
eth0: 00:03:7f:09:0b:ad
eth1: 00:03:7f:09:0b:ad
eth0, eth1
Setting 0x181162c0 to 0x4d9a2100
Net cmd check.
eth0 link down
enet1 port3 up
dup 1 speed 1000
Hit any key to stop autoboot:  0
## Booting image at 9f028000 ...
Magic: 13a787b8
Bad Magic Number
Failed to boot.
Starting httpd to update firmware...
starting httpd server eth1 192.168.17.1
Alloc 192.168.17.3 to 00:1f:c6:6c:83:09
Request for: /
Request for: /style.css
Request for: /favicon.ico
File not found!
Data will be downloaded at 0x80060000 in RAM
Upload file size: 1855688 bytes
#######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #######################################
         #####################################

Image magic: 5370eb67
Write firmware (0x1c4f8c) to 0x9f028000
Erasing flash...
First 0x28 last 0x1ff sector size 0x1000
=== erase   40 4k
=== erase   41 4k
=== erase   42 4k
=== erase   43 4k
=== erase   44 4k
=== erase   45 4k
=== erase   46 4k
=== erase   47 4k
=== erase   48 64k
=== erase   64 64k
=== erase   80 64k
=== erase   96 64k
=== erase  112 64k
=== erase  128 64k
=== erase  144 64k
=== erase  160 64k
=== erase  176 64k
=== erase  192 64k
=== erase  208 64k
=== erase  224 64k
=== erase  240 64k
=== erase  256 64k
=== erase  272 64k
=== erase  288 64k
=== erase  304 64k
=== erase  320 64k
=== erase  336 64k
=== erase  352 64k
=== erase  368 64k
=== erase  384 64k
=== erase  400 64k
=== erase  416 64k
=== erase  432 64k
=== erase  448 64k
=== erase  464 64k
=== erase  480 64k
=== erase  496 64k
Erased 472 sectors
Copy to Flash... write addr: 9f028000
done


U-Boot 1.1.4-g49d3d3a1-dirty (Dec  4 2015 - 12:58:31)

tl-wr886n-v5 - Dragonfly 1.0

DRAM:  16 MB
Flash:  2 MB (c84015)
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   Dragonfly----> S27 PHY *
eth0: 00:03:7f:09:0b:ad
eth1: 00:03:7f:09:0b:ad
eth0, eth1
Setting 0x181162c0 to 0x4d9a2100
Net cmd check.
eth0 link down
enet1 port3 up
dup 1 speed 1000
Hit any key to stop autoboot:  0
## Booting image at 9f028000 ...
   Image Name:   SuperWrt qca/ar934x/tiny
   Created:      2015-12-04   7:13:51 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    881664 Bytes = 861 kB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9f028040 ...OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.8 (terra@localhost.localdomain) (gcc version 4.8.3 (SuperWrt/Linaro GCC 4.8-2014.04 r44747) ) #2 Fri Dec 4 15:13:48 CST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] SoC: Qualcomm Atheros TP9343 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 01000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 01000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x00ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x00ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x00ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
[    0.000000] Kernel command line:  console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=spi0.0:32k(lite-uboot),96k(rtboot),4k(ART),28k(config),1888k(firmware) mem=16M rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
[    0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 13168K/16384K available (2049K kernel code, 94K rwdata, 268K rodata, 140K init, 83K bss, 3216K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:750.000MHz, DDR:400.000MHz, AHB:250.000MHz, Ref:25.000MHz
[    0.000000] Calibrating delay loop... 374.78 BogoMIPS (lpj=749568)
[    0.028000] pid_max: default: 4096 minimum: 301
[    0.032000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.036000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] NET: Registered protocol family 16
[    0.044000] MIPS: machine is SuperWRT
[    0.464000] Switched to clocksource MIPS
[    0.468000] NET: Registered protocol family 2
[    0.472000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.476000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.484000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.492000] TCP: reno registered
[    0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.500000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.504000] NET: Registered protocol family 1
[    0.508000] futex hash table entries: 16 (order: -5, 192 bytes)
[    0.520000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.524000] io scheduler noop registered
[    0.528000] io scheduler deadline registered (default)
[    0.536000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
奫    0.564000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.572000] console [ttyS0] enabled
[    0.572000] console [ttyS0] enabled
[    0.580000] bootconsole [early0] disabled
[    0.580000] bootconsole [early0] disabled
[    0.588000] m25p80 spi0.0: found gd25q16, expected m25p80
[    0.596000] m25p80 spi0.0: gd25q16 (2048 Kbytes)
[    0.600000] 5 cmdlinepart partitions found on MTD device spi0.0
[    0.604000] Creating 5 MTD partitions on "spi0.0":
[    0.612000] 0x000000000000-0x000000008000 : "lite-uboot"
[    0.616000] 0x000000008000-0x000000020000 : "rtboot"
[    0.624000] 0x000000020000-0x000000021000 : "ART"
[    0.628000] 0x000000021000-0x000000028000 : "config"
[    0.632000] 0x000000028000-0x000000200000 : "firmware"
[    0.640000] Support for built-in firmware splitter will be removed, please use CONFIG_MTD_SPLIT_UIMAGE_FW
[    0.648000] 0x0000000ff440-0x000000200000 : "rootfs"
[    0.656000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.668000] mtd: device 5 (rootfs) set to be root filesystem
[    0.676000] 1 squashfs-split partitions found on MTD device rootfs
[    0.680000] 0x0000001ed000-0x000000200000 : "rootfs_data"
[    0.692000] libphy: ag71xx_mdio: probed
[    1.264000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.272000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.848000] ag71xx-mdio.1: Found an AR934X built-in switch
[    1.888000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    1.892000] PPP generic driver version 2.4.2
[    1.900000] PPP MPPE Compression module registered
[    1.904000] NET: Registered protocol family 24
[    1.908000] PPTP driver version 0.8.5
[    1.912000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[    1.920000] nf_conntrack version 0.5.0 (205 buckets, 820 max)
[    1.928000] gre: GRE over IPv4 demultiplexor driver
[    1.932000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.940000] TCP: cubic registered
[    1.940000] NET: Registered protocol family 17
[    1.948000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.964000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.972000] Freeing unused kernel memory: 140K (802bd000 - 802e0000)
init started: BusyBox v1.22.1 (2015-12-04 12:48:28 CST)
starting pid 36, tty '': 'sh /etc/init.d/rcS S start'
mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
mount: mounting devpts on /dev/pts failed: No such file or directory
mount: mounting nodev on /sys/kernel/debug failed: No such file or directory
cat: can't open '/var/run/watchdog.pid': No such file or directory
/etc/rc.d/S10boot: line 40: can't create /proc//oom_score_adj: nonexistent directory
[    3.944000] Loading modules backported from Linux version master-2015-10-26-0-g28c26cb
[    3.952000] Backport generated by backports.git backports-20150903-4-g12cf266
[    3.980000] cfg80211: World regulatory domain updated:
[    3.984000] cfg80211:  DFS Master region: unset
[    3.988000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    4.000000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    4.008000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    4.016000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    4.024000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    4.032000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[    4.044000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    4.052000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    4.060000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    4.488000] ath: phy0: both bands are disabled
[    4.492000] ath: phy0: Unable to initialize hardware; initialization status: -22
[    4.500000] ath9k qca956x_wmac: failed to initialize device
[    4.508000] ath9k: probe of qca956x_wmac failed with error -22
[    5.052000] random: svld urandom read with 20 bits of entropy available
killall: hostapd: no process killed
[    5.544000] device eth1 entered promiscuous mode
[    5.592000] lan: port 1(eth1) entered forwarding state
[    5.600000] lan: port 1(eth1) entered forwarding state
killall: udhcpd: no process killed
killall: pppoec: no process killed
killall: udhcpc: no process killed
[    6.548000] lan: port 1(eth1) entered disabled state
route: SIOCDELRT: No such process
ifconfig: invalid hw-addr up
udhcpc (v1.22.1) started
Setting IP address 0.0.0.0 on eth0
Sending discover...
killall: pptpc: no process killed
Jan  1 00:00:06 crond[209]: crond: crond (busybox 1.22.1) started, log level 8

Please press Enter to activate this console. [    7.688000] eth1: link up (1000Mbps/Full duplex)
[    7.692000] lan: port 1(eth1) entered forwarding state
[    7.696000] lan: port 1(eth1) entered forwarding state
Sending discover...
Sending discover...
No lease, forking to background
[   32.564000] random: nonblocking pool is initialized
[  105.192000] eth1: link down
[  105.192000] lan: port 1(eth1) entered disabled state
[  107.692000] eth1: link up (1000Mbps/Full duplex)
[  107.696000] lan: port 1(eth1) entered forwarding state
[  107.700000] lan: port 1(eth1) entered forwarding state

starting pid 212, tty '': '/sbin/getty -L -a'

SuperWRT login: root
Password:

Login incorrect
SuperWRT login: root
Password:
Login incorrect
SuperWRT login:
process '/sbin/getty -L -a' (pid 212) exited. Scheduling for restart.

忘了我吧Android

两百米 ， 没有只能看看了。

舞叶

这东西好高大上啊

天生的心

求共享编辑器固件！

没有ttl

Free_like_a_bir

天生的心 发表于 2015-12-8 08:01
求共享编辑器固件！

没有ttl

得换uboot，原版uboot不支持，你有编程器？可以TTL啊.

visions

ar9331的有得玩吗？有个fw150rm。

Free_like_a_bir

visions 发表于 2015-12-8 08:52
ar9331的有得玩吗？有个fw150rm。

不是我开发的，直奔http://www.anywlan.com/thread-380607-1-1.html找楼主问问。

hhhmnsl

看来得学学tll了 v2版本能刷么？

terracoding

感谢支持。好像你的设备没校准信息。或者校准信息不在原厂的位置。

Free_like_a_bir

terracoding 发表于 2015-12-8 13:01
感谢支持。好像你的设备没校准信息。或者校准信息不在原厂的位置。

貌似是的没有无线

visions

Free_like_a_bir 发表于 2015-12-8 09:08
不是我开发的，直奔http://www.anywlan.com/thread-380607-1-1.html找楼主问问。

好的，多谢！！

cloudqd

用了一阵子Superwrt,最近看到官方有升级，就升级了，但是升级之后为啥多了一个广告SSID ?请解释一下这个开启SSID广告为啥会增加抗干扰特性；我家住的小区，2.4G无线干扰严重，随便一搜都能接近上百信号，可我不管是勾选还是不勾选，测试了一下无线下载上传速度，基本都差不多呀，唯一的区别就是勾选后多出来一个广告SSID！多这么一个ID不是白白增加负载占用内存么？难道增加SSID就可以抗干扰么？哪有这道理？还有就是如果想要做广告，能不能考虑其他方式？