求大神帮忙分析一下，wr800n v1+usb 刷842ND V2+breed 又有问题(已解决)

群山望月

问题已解决，请看4楼
wr800n v1 +USB（D+D-只接了下拉15k电阻和5V供电，没有接22欧电阻，试了50欧代替22欧接了也不行）能刷842ND V2，今天刷了H大神的最新的 Breed r777 [2015-10-18]，可以正常启动了，但是用842NDV2官方的uboot和大神的不死uboot，就是偶尔启动成功
今天刷了Breed 测试了800N V1的 RESET GPIO#18
breed> btntst
Press Ctrl+C to stop.

GPIO#18 changed to 0
GPIO#18 changed to 1

breed> gpio led
GPIO    status  name
11      off     usb
12      off     lan4
13      off     wlan
14      on      sys
15      off     qss
18      off     wan
19      off     lan1
20      off     lan2
21      off     lan3breed> gpio
GPIO    direction   status  name
0       in          lo      
1       in          lo      
2       out         lo      
3       in          lo      
4       out         lo      
5       out         hi      
6       out         lo      
7       out         lo      
8       in          lo      
9       in          hi      
10      out         lo      
11      out         hi      usb
12      out         hi      lan4
13      out         hi      wlan
14      out         hi      sys
15      out         hi      qss
16      in          hi      wps
17      in          hi      reset
18      out         hi      wan
19      out         hi      lan1
20      out         hi      lan2
21      out         hi      lan3
22      out         lo  


启动TTL信息
===================================
Boot and Recovery Environment for EmbeddedDevices
Copyright (C) 2015 HackPascal<hackpascal@gmail.com>
Build date 2015-10-18 [git-bb5218f]
Version 1.0 (r777)

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB:200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: MAC address is invalid, usingdefault settings.
ag71xx-eth: Using MAC address00:13:74:00:00:01
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ...0   

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
   Image Name:   08420002
   Data Size:    845472 Bytes
   Load Address: 80002000
   Entry Point:  801aeb70
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x801aeb70...

Booting Atheros AR934x
Linux version 2.6.31--LSDK-9.2.0_U5.508(root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #3 Fri Jun 28 10:10:08CST 2013
flash_size passed from bootloader = 8
Ram size passed from bootloader =33554432
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu560 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
Normal   0x00000000 ->0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
   0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobilitygrouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200root=31:2 rootfstype=squashfs init=/sbin/initmtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(art)mem=32M
PID hash table entries: 128 (order: 7, 512bytes)
Dentry cache hash table entries: 4096(order: 2, 16384 bytes)
Inode-cache hash table entries: 2048(order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT,4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cachealiases, linesize 32 bytes
Writing ErrCtl register=000000c0
Readback ErrCtl register=000000c0
Memory: 30036k/32768k available (1742kkernel code, 2732k reserved, 498k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS(lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024(order: 0, 4096 bytes)
TCP established hash table entries: 1024(order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order:0, 4096 bytes)
TCP: Hash tables configured (established1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) PhillipLougher
msgmni has been set to 58
alg: No test for cipher_null(cipher_null-generic)
alg: No test for ecb(cipher_null)(ecb-cipher_null)
alg: No test for digest_null(digest_null-generic)
alg: No test for compress_null(compress_null-generic)
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
alg: No test for stdrng (ansi_cprng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQsharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq= 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTDdevice ath-nor0
Creating 5 MTD partitions on"ath-nor0":
0x000000000000-0x000000020000 :"u-boot"
0x000000020000-0x000000120000 :"kernel"
0x000000120000-0x0000007e0000 :"rootfs"
0x0000007e0000-0x0000007f0000 :"config"
0x0000007f0000-0x000000800000 :"art"
->Oops: flash id 0xef4017 .
Ooops, why the devices couldn't beeninitialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear<greearb@candelatech.com>
All bugs added by David S. Miller<davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock SwitchInterface success
VFS: Mounted root (squashfs filesystem)readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started:  BusyBox v1.01 (2013.06.28-02:15+0000)multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets,5120 max)
CONFIG_NF_CT_ACCT is deprecated and will beremoved soon. Please use
nf_conntrack.acct=1 kernel parameter,acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 toenable it.
ip_tables: (C) 2000-2006 Netfilter CoreTeam
insmod: cannot open module`/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module`/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module`/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
NET: Registered protocol family 15
Initializing XFRM netlink socket
/proc/sys/vfs_c
Now flash open!
(none) mips #3 Fri Jun 28 10:10:08 CST 2013(none)
(none) login: Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :  2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :  2582
athr_gmac_ring_alloc Allocated 640 at0x81ebc800
athr_gmac_ring_alloc Allocated 2048 at0x81cb7000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at0x81e30c00
athr_gmac_ring_alloc Allocated 2048 at0x81e3e000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
Setting PHY...
device eth0 entered promiscuous mode
athr_gmac_ring_free Freeing at 0x81e30c00
athr_gmac_ring_free Freeing at 0x81e3e000
athr_gmac_ring_alloc Allocated 640 at0x81e30c00
athr_gmac_ring_alloc Allocated 2048 at0x81f0d800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
Setting PHY...
Now flash open!
athr_gmac_ring_free Freeing at 0x81ebc800
athr_gmac_ring_free Freeing at 0x81cb7000
athr_gmac_ring_alloc Allocated 640 at0x81ebc800
athr_gmac_ring_alloc Allocated 2048 at0x81ea0800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
Setting PHY...
enet1 port4 up
ATHR_GMAC: Enet Unit:1 PHY:4 is UP RGMii100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0miictrl  
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
br0: port 1(eth0) entering forwarding state
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taintskernel.
Disabling lock debugging due to kerneltaint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC,WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 AtherosCommunications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
ath_get_caps[5113] rx chainmask mismatchactual 3 sc_chainmak 0
ath_get_caps[5088] tx chainmask mismatchactual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
wlan_vap_create : enter.devhandle=0x80d682c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit.devhandle=0x80d682c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created


***********************************

DESSSID SET=TP-LINK_137B00
ieee80211_ioctl_siwmode:imr.ifm_active=131712, new mode=3, valid=1


***********************************
athr_gmac_ring_free Freeing at 0x81ebc800
athr_gmac_ring_free Freeing at 0x81ea0800
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 640 at0x81ebc800
athr_gmac_ring_alloc Allocated 2048 at0x81ea0000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
Setting PHY...


***********************************
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode:imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DESSSID SET=TP-LINK_137B00


***********************************
br0: port 2(ath0) entering forwarding state
enet1 port4 up
ATHR_GMAC: Enet Unit:1 PHY:4 is UP RGMii100Mbps full duplex
ATHR_GMAC: done cfg2 0x7215 ifctl 0x0miictrl  
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames andLength Error frames
br0: port 1(eth0) entering forwarding state
fuse init (API version 7.12)
usbcore: registered new interface driverusbfs
usbcore: registered new interface driverhub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' HostController (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB busregistered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in hostmode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem0x1b000000
ehci_reset Intialize USB CONTROLLER in hostmode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI1.00
usb usb1: configuration #1 chosen from 1choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driverusb-storage
USB Mass Storage support registered.
kcg 323 :GPL NetUSB up!
kc  90 : run_telnetDBGDServer start
kc 227 : init_DebugD end
INFO17B7: NetUSB 1.02.29, 0002061F : Dec 112012 10:20:50
INFO17B9: AUTH ISOC
INFO17BA: filterAudio
usbcore: registered new interface driver KCNetUSB General Driver
INFO0110: init proc : PAGE_SIZE 4096
INFO1819: Check mac address
INFO168B: infomap c0f5bf20
INFO168E: sleep to wait br0 to wake up
INFO02D0: use dev Name br0
INFO1697: sleep to wait br0 end.
INFO16B0: UDP_BROAD 7437 tcpPort:625868800
INFO02D0: use dev Name br0
INFO1597: tcpConnector() started...
ATHR_GMAC: GE0 RX DMA ENABLE
INFO1474: Bind to br0

群山望月

800nV1刷9341通用breed+842NDV2固件，挂了u盘，启动没问题，就是电脑无线（有线没有问题）连接路由，就出现u盘不断的掉线
可以排除u盘问题，试了很多个u盘都不行，这些U盘在其他路由可以挂载
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2015 HackPascal <hackpascal@gmail.com>
Build date 2015-10-18 [git-bb5218f]
Version 1.0 (r777)

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0   

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
    Image Name:   08420002
    Data Size:    845472 Bytes
    Load Address: 80002000
    Entry Point:  801aeb70
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x801aeb70...

Booting Atheros AR934x
Linux version 2.6.31--LSDK-9.2.0_U5.508 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #3 Fri Jun 28 10:10:08 CST 2013
flash_size passed from bootloader = 8
Ram size passed from bootloader =33554432
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=000000c0
Readback ErrCtl register=000000c0
Memory: 30036k/32768k available (1742k kernel code, 2732k reserved, 498k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 58
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
alg: No test for stdrng (ansi_cprng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000007e0000 : "rootfs"
0x0000007e0000-0x0000007f0000 : "config"
0x0000007f0000-0x000000800000 : "art"
->Oops: flash id 0xef4017 .
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started:  BusyBox v1.01 (2013.06.28-02:15+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets, 5120 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
NET: Registered protocol family 15
Initializing XFRM netlink socket
/proc/sys/vfs_c
Now flash open!
(none) mips #3 Fri Jun 28 10:10:08 CST 2013 (none)
(none) login: Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2582
athr_gmac_ring_alloc Allocated 640 at 0x81ea6800
athr_gmac_ring_alloc Allocated 2048 at 0x81cb7000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x81ec6c00
athr_gmac_ring_alloc Allocated 2048 at 0x81e31000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0 entered promiscuous mode
athr_gmac_ring_free Freeing at 0x81ec6c00
athr_gmac_ring_free Freeing at 0x81e31000
athr_gmac_ring_alloc Allocated 640 at 0x81ec6c00
athr_gmac_ring_alloc Allocated 2048 at 0x81f0d800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Now flash open!
athr_gmac_ring_free Freeing at 0x81ea6800
athr_gmac_ring_free Freeing at 0x81cb7000
athr_gmac_ring_alloc Allocated 640 at 0x81ea6800
athr_gmac_ring_alloc Allocated 2048 at 0x81e98800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
ath_get_caps[5113] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5088] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
wlan_vap_create : enter. devhandle=0x80c1c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x80c1c2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created


***********************************

DES SSID SET=TP-LINK_AFCC16
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1


***********************************
athr_gmac_ring_free Freeing at 0x81ea6800
athr_gmac_ring_free Freeing at 0x81e98800
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 640 at 0x81ea6800
athr_gmac_ring_alloc Allocated 2048 at 0x81e98000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...


***********************************
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DES SSID SET=TP-LINK_AFCC16


***********************************
br0: port 2(ath0) entering forwarding state
fuse init (API version 7.12)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
SCSI subsystem initialized
usb 1-1: new high speed USB device using ath-ehci and address 2
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
kcg 323 :GPL NetUSB up!
kc   90 : run_telnetDBGDServer start
kc  227 : init_DebugD end
INFO17B7: NetUSB 1.02.29, 0002061F : Dec 11 2012 10:20:50
INFO17B9:  AUTH ISOC
INFO17BA:  filterAudio
usbcore: registered new interface driver KC NetUSB General Driver
INFO0110:  init proc : PAGE_SIZE 4096
INFO1819: Check mac address
INFO168B:  infomap c0f5bf20
INFO168E:  sleep to wait br0 to wake up
INFO02D0:  use dev Name br0
INFO1697:  sleep to wait br0 end.
INFO16B0:  UDP_BROAD 7437 tcpPort:625868800
INFO02D0:  use dev Name br0
INFO1597: tcpConnector() started...
ATHR_GMAC: GE0 RX DMA ENABLE
INFO1474: Bind to br0
scsi 0:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 2
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: new high speed USB device using ath-ehci and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
scsi 1:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 1:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 1-1: USB disconnect, address 3
sd 1:0:0:0: [sda] Unhandled error code
sd 1:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 11338
sd 1:0:0:0: [sda] Unhandled error code
sd 1:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 11339
sd 1:0:0:0: [sda] Unhandled error code
sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
end_request: I/O error, dev sda, sector 11340
FAT: FAT read failed (blocknr 3274)
FAT: FAT read failed (blocknr 3274)
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: new high speed USB device using ath-ehci and address 4
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 4
usb 1-1: new high speed USB device using ath-ehci and address 5
usb 1-1: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
scsi 3:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 3:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Assuming drive cache: write through
sd 3:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 3:0:0:0: [sda] Assuming drive cache: write through
sd 3:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
usb 1-1: USB disconnect, address 5
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 10761
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 10762
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
end_request: I/O error, dev sda, sector 10763
FAT: FAT read failed (blocknr 2697)
FAT: FAT read failed (blocknr 2697)
usb 1-1: new high speed USB device using ath-ehci and address 6
usb 1-1: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
scsi 4:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 4:0:0:0: Attached scsi generic sg0 type 0
sd 4:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 4:0:0:0: [sda] Assuming drive cache: write through
sd 4:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 6
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: new high speed USB device using ath-ehci and address 7
usb 1-1: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
scsi 5:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 5:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 5:0:0:0: Attached scsi generic sg0 type 0
sd 5:0:0:0: [sda] Write Protect is off
sd 5:0:0:0: [sda] Assuming drive cache: write through
sd 5:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 5:0:0:0: [sda] Assuming drive cache: write through
sd 5:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 7
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
usb 1-1: new high speed USB device using ath-ehci and address 8
usb 1-1: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 8
usb 1-1: new high speed USB device using ath-ehci and address 9
usb 1-1: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb 1-1: USB disconnect, address 9
usb 1-1: new high speed USB device using ath-ehci and address 10
usb 1-1: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
scsi 8:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
sd 8:0:0:0: Attached scsi generic sg0 type 0
sd 8:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 8:0:0:0: [sda] Write Protect is off
sd 8:0:0:0: [sda] Assuming drive cache: write through
sd 8:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 8:0:0:0: [sda] Assuming drive cache: write through
sd 8:0:0:0: [sda] Attached SCSI removable disk
SQUASHFS error: Can't find a SQUASHFS superblock on sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0xb9)
VFS: Can't find a valid FAT filesystem on dev sda.
SQUASHFS error: Can't find a SQUASHFS superblock on sda1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully
usb 1-1: USB disconnect, address 10
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
usb 1-1: new high speed USB device using ath-ehci and address 11
usb 1-1: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
Now flash open!
Erase from 0X7E0000 to 0X7EB124:.
Program from 0X7E0000 to 0X7EB124:
write successfully

群山望月

刷了明月的op 还是不能 无线连接路由，一连接就这样

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 3   
Autoboot aborted due to Breed Enter.

Starting breed built-in shell

breed> Upgrade completed.
Rebooting in 2 seconds ...
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2015 HackPascal <hackpascal@gmail.com>
Build date 2015-10-18 [git-bb5218f]
Version 1.0 (r777)

DRAM: 32MB
Platform: Atheros AR9341 rev 3
Board: Atheros AP123 reference board
Clocks: CPU: 560MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz
Flash: Winbond W25Q64 (8MB) on ath79-spi
ag71xx-eth: Using MAC address 0c:82:68:af:cc:16
eth0: Atheros AR8228/AR8229 rev 1

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0   

Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
    Image Name:   08420002
    Data Size:    1064028 Bytes
    Load Address: 80060000
    Entry Point:  80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80060000...

[    0.000000] Linux version 3.10.70 (yong@yong-pc) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44550) ) #3 Sat Mar 7 01:21:49 CST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 3
[    0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR842N-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=000000c0
[    0.000000] Readback ErrCtl register=000000c0
[    0.000000] Memory: 28720k/32768k available (2257k kernel code, 4048k reserved, 600k data, 276k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR842N/ND v2
[    0.510000] bio: create slab <bio-0> at 0
[    0.510000] Switching to clocksource MIPS
[    0.520000] NET: Registered protocol family 2
[    0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.540000] TCP: Hash tables configured (established 512 bind 512)
[    0.540000] TCP: reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.590000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.610000] io scheduler deadline registered (default)
[    0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.650000] console [ttyS0] enabled, bootconsole disabled
[    0.660000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.670000] m25p80 spi0.0: found w25q64, expected m25p80
[    0.670000] m25p80 spi0.0: w25q64 (8192 Kbytes)
[    0.680000] 6 tp-link partitions found on MTD device spi0.0
[    0.690000] Creating 6 MTD partitions on "spi0.0":
[    0.690000] 0x000000000000-0x000000020000 : "u-boot"
[    0.700000] 0x000000020000-0x000000123e5c : "kernel"
[    0.700000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.720000] 0x000000123e5c-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.740000] mtd: device 2 (rootfs) set to be root filesystem
[    0.740000] 1 squashfs-split partitions found on MTD device rootfs
[    0.750000] 0x000000760000-0x0000007f0000 : "rootfs_data"
[    0.760000] 0x0000007f0000-0x000000800000 : "art"
[    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.770000] 0x000000000000-0x000000800000 : "fullflash"
[    0.790000] libphy: ag71xx_mdio: probed
[    1.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.920000] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.950000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.960000] TCP: cubic registered
[    2.960000] NET: Registered protocol family 17
[    2.970000] Bridge firewalling registered
[    2.970000] 8021q: 802.1Q VLAN Support v1.8
[    2.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.990000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
procd: Console is alive
procd: - watchdog -
[    7.480000] usbcore: registered new interface driver usbfs
[    7.480000] usbcore: registered new interface driver hub
[    7.490000] usbcore: registered new device driver usb
[    7.540000] SCSI subsystem initialized
[    7.550000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.560000] ehci-platform: EHCI generic platform driver
[    7.560000] ehci-platform ehci-platform: EHCI Host Controller
[    7.570000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    7.580000] ehci-platform ehci-platform: TX-TX IDP fix enabled
[    7.590000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    7.610000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    7.610000] hub 1-0:1.0: USB hub found
[    7.620000] hub 1-0:1.0: 1 port detected
[    7.620000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.630000] uhci_hcd: USB Universal Host Controller Interface driver
[    7.640000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[    8.210000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    8.360000] usb-storage 1-1:1.0: USB Mass Storage device detected
[    8.370000] scsi0 : usb-storage 1-1:1.0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.430000] scsi 0:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[   10.190000] sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   10.200000] sd 0:0:0:0: [sda] Write Protect is off
[   10.200000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.210000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.220000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.220000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.250000]  sda: sda1
[   10.260000] sd 0:0:0:0: [sda] No Caching mode page found
[   10.260000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   10.270000] sd 0:0:0:0: [sda] Attached SCSI removable disk
block: extroot: failed to load /etc/config/fstab: Entry not found
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   19.580000] NET: Registered protocol family 8
[   19.580000] NET: Registered protocol family 20
[   19.600000] tun: Universal TUN/TAP device driver, 1.6
[   19.600000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   19.620000] l2tp_core: L2TP core driver, V2.0
[   19.620000] l2tp_netlink: L2TP netlink interface
[   19.640000] gre: GRE over IPv4 demultiplexor driver
[   19.640000] ip_gre: GRE over IPv4 tunneling driver
[   19.660000] PPP generic driver version 2.4.2
[   19.670000]  Hooked IMQ after mangle on PREROUTING
[   19.680000]  Hooked IMQ after nat on POSTROUTING
[   19.680000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   19.690000]  Hooking IMQ before NAT on PREROUTING.
[   19.700000]  Hooking IMQ after NAT on POSTROUTING.
[   19.710000] Netfilter messages via NETLINK v0.30.
[   19.710000] ip_set: protocol 6
[   19.760000] ufsd: module license 'Commercial product' taints kernel.
[   19.760000] Disabling lock debugging due to kernel taint
[   19.790000] ufsd:: trace mask set to 0000000f
[   19.790000] ufsd: driver (lke_8.9.0 lke_8.9.0_22, LBD=ON, delalloc, ioctl, bdi, sd2, fua, tr) loaded at 80400000
[   19.790000] NTFS support included
[   19.790000] Big endian platform
[   19.790000] optimized: speed
[   19.790000] Build_for__ASUS_PRODUCTS_005_k2.6.22.15_2013-11-20_lke_8.9.0_r217400_b3
[   19.790000]
[   19.830000] u32 classifier
[   19.840000]     input device check on
[   19.840000]     Actions configured
[   19.850000] Mirror/redirect action on
[   19.860000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   19.870000] Failed to load ipt action
[   19.910000] fuse init (API version 7.22)
[   19.920000] arp_tables: (C) 2002 David S. Miller
[   19.930000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   19.940000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   19.980000] Ebtables v2.0 registered
[   20.000000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.080000] PPP MPPE Compression module registered
[   20.100000] NET: Registered protocol family 24
[   20.100000] PPTP driver version 0.8.5
[   20.120000] usbcore: registered new interface driver ums-alauda
[   20.140000] usbcore: registered new interface driver ums-cypress
[   20.160000] usbcore: registered new interface driver ums-datafab
[   20.170000] usbcore: registered new interface driver ums-freecom
[   20.170000] usbcore: registered new interface driver ums-isd200
[   20.190000] usbcore: registered new interface driver ums-jumpshot
[   20.210000] usbcore: registered new interface driver ums-karma
[   20.230000] usbcore: registered new interface driver ums-sddr09
[   20.240000] usbcore: registered new interface driver ums-sddr55
[   20.240000] usbcore: registered new interface driver ums-usbat
[   20.380000] xt_time: kernel timezone is -0000
[   20.460000] cfg80211: Calling CRDA to update world regulatory domain
[   20.460000] cfg80211: World regulatory domain updated:
[   20.470000] cfg80211:  DFS Master region: unset
[   20.470000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   20.480000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.490000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.500000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   20.510000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   20.520000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.530000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.530000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   20.540000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   20.560000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   20.740000] usbcore: registered new interface driver rtl8187
[   22.320000] usbcore: registered new interface driver rt2800usb
[   23.180000] cfg80211: Calling CRDA for country: US
[   23.200000] cfg80211: Regulatory domain changed to country: US
[   23.200000] cfg80211:  DFS Master region: FCC
[   23.210000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   23.220000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   23.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2700 mBm), (N/A)
[   23.230000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
[   23.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   23.250000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   23.260000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[   48.010000] device eth1 entered promiscuous mode
[   52.420000] device wlan0 entered promiscuous mode
[   52.420000] br-lan: port 2(wlan0) entered forwarding state
[   52.430000] br-lan: port 2(wlan0) entered forwarding state
[   52.800000] eth0: link up (100Mbps/Full duplex)
[   52.800000] br-lan: port 2(wlan0) entered disabled state
[   55.930000] br-lan: port 2(wlan0) entered forwarding state
[   55.930000] br-lan: port 2(wlan0) entered forwarding state
[   57.930000] br-lan: port 2(wlan0) entered forwarding state
[   73.500000] eth0: link down
[   85.280000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   85.310000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   85.310000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   87.740000] jffs2: notice: (2699) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   89.790000] usb 1-1: USB disconnect, device number 2
[   90.110000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[   90.270000] usb-storage 1-1:1.0: USB Mass Storage device detected
[   90.270000] scsi1 : usb-storage 1-1:1.0
[   91.290000] scsi 1:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[   91.690000] sd 1:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   91.720000] sd 1:0:0:0: [sda] Write Protect is off
[   91.720000] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[   91.750000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.750000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.780000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.790000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.820000]  sda: sda1
[   91.830000] sd 1:0:0:0: [sda] No Caching mode page found
[   91.840000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   91.840000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   97.100000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
procd: - init complete -
[  134.140000] usb 1-1: USB disconnect, device number 3
[  134.440000] usb 1-1: new high-speed USB device number 4 using ehci-platform
[  134.600000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  134.600000] scsi2 : usb-storage 1-1:1.0
[  135.150000] usb 1-1: USB disconnect, device number 4
[  135.450000] usb 1-1: new high-speed USB device number 5 using ehci-platform
[  135.600000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  135.620000] scsi3 : usb-storage 1-1:1.0
[  136.620000] scsi 3:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[  136.630000] sd 3:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  136.640000] sd 3:0:0:0: [sda] Write Protect is off
[  136.650000] sd 3:0:0:0: [sda] Mode Sense: 23 00 00 00
[  136.650000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.660000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.670000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.680000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.680000]  sda: sda1
[  136.700000] sd 3:0:0:0: [sda] No Caching mode page found
[  136.710000] sd 3:0:0:0: [sda] Assuming drive cache: write through
[  136.710000] sd 3:0:0:0: [sda] Attached SCSI removable disk
[  138.720000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  140.670000] usb 1-1: USB disconnect, device number 5
[  140.960000] usb 1-1: new high-speed USB device number 6 using ehci-platform
[  141.120000] usb-storage 1-1:1.0: USB Mass Storage device detected
[  141.120000] scsi4 : usb-storage 1-1:1.0
[  142.130000] scsi 4:0:0:0: Direct-Access     Netac    OnlyDisk         PMAP PQ: 0 ANSI: 6
[  142.140000] sd 4:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[  142.150000] sd 4:0:0:0: [sda] Write Protect is off
[  142.160000] sd 4:0:0:0: [sda] Mode Sense: 23 00 00 00
[  142.160000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.170000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.180000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.190000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.190000]  sda: sda1
[  142.210000] sd 4:0:0:0: [sda] No Caching mode page found
[  142.220000] sd 4:0:0:0: [sda] Assuming drive cache: write through
[  142.220000] sd 4:0:0:0: [sda] Attached SCSI removable disk
[  143.330000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

群山望月

本人估计是布线的问题，原来usb data数据线布线距离wifi天线（也有可能是晶振太近了），所以电脑或手机无线连接路由，usb挂载就掉线->重新挂载->掉线->重新挂载.......，有时候进入死循环后来把usb data数据线布线距离wifi天线远了一点，因为空间有限。附上两幅图给大家参考，见1楼。



唯一遗憾是没有wlan口了，842ND V2 wlan口是lan4，想要用wlan口刷op也行，可以wlan/lan合一。


注意9341 的通用breed ，reset gpio是17，而800n V1 reset gpio是18，想要进breed刷固件，reset失灵了，只能ttl或用breedenter 。


若刷了tp官方的uboot+842ND V2 固件（会不断重启），想刷breed 只能先刷op（tp官方的uboot 网口是wlan口），用op刷breed（方法和刷uboot一样，别忘了改为wlan/lan合一，不然没有lan口，当燃也可以用wlan口SSH也未尝不可）。

gutou10

不知道楼主表达什么，看不懂日志

群山望月

gutou10 发表于 2015-11-2 10:05
不知道楼主表达什么，看不懂日志

不用看了，不是哪里的问题

ywj96960

不是应该用屏蔽线吗