少校
- 注册时间
- 2013-7-31
- 金币
- 4075 个
- 威望
- 2 个
- 荣誉
- 1 个
累计签到:394 天 连续签到:1 天 [LV.730]常住居民
|
发表于 2015-5-16 23:33
本帖最后由 dong0620 于 2015-5-16 23:36 编辑
不会排版请谅解!
QCA9533有两个版本,QCA9533 BL3A和QCA9533 AL3A
个人简称B版和A版!本贴实测与老手交流,新手分享,底部有固件B版
老规矩上日志
[ 0.000000] Linux version 3.14.29 (lin@lin-laptop) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44154) ) #11 Tue Jan 27 23:51:04 CST 2015
[ 0.000000] MyLoader: sysp=ee4ad530, boardp=8b61f71b, parts=dbcb080c
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80336420, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR841N-v9 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=000266c0
[ 0.000000] Readback ErrCtl register=000266c0
[ 0.000000] Memory: 28652K/32768K available (2372K kernel code, 120K rwdata, 500K rodata, 200K init, 187K bss, 4116K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is TP-LINK TL-WR841N/ND v9
[ 0.540000] bio: create slab <bio-0> at 0
[ 0.550000] Switched to clocksource MIPS
[ 0.550000] NET: Registered protocol family 2
[ 0.560000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.580000] TCP: reno registered
[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.600000] PCI: CLS 0 bytes, default 32
[ 0.600000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.650000] msgmni has been set to 55
[ 0.650000] io scheduler noop registered
[ 0.650000] io scheduler deadline registered (default)
[ 0.660000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.700000] console [ttyS0] enabled
[ 0.700000] bootconsole [early0] disabled
[ 0.720000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.720000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.730000] 5 tp-link partitions found on MTD device spi0.0
[ 0.730000] Creating 5 MTD partitions on "spi0.0":
[ 0.740000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.750000] 0x000000020000-0x00000012e0b8 : "kernel"
[ 0.750000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.770000] 0x00000012e0b8-0x0000007f0000 : "rootfs"
[ 0.770000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.790000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.790000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.800000] 0x000000360000-0x0000007f0000 : "rootfs_data"
[ 0.810000] 0x0000007f0000-0x000000800000 : "art"
[ 0.810000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.850000] libphy: ag71xx_mdio: probed
[ 1.440000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.480000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.080000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.090000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.100000] TCP: cubic registered
[ 2.100000] NET: Registered protocol family 17
[ 2.110000] 8021q: 802.1Q VLAN Support v1.8
[ 2.120000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.130000] Freeing unused kernel memory: 200K (8034e000 - 80380000)
[ 4.330000] usbcore: registered new interface driver usbfs
[ 4.330000] usbcore: registered new interface driver hub
[ 4.340000] usbcore: registered new device driver usb
[ 4.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.360000] ehci-platform: EHCI generic platform driver
[ 4.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.380000] ohci-platform: OHCI generic platform driver
[ 5.810000] random: mktemp urandom read with 58 bits of entropy available
[ 7.360000] eth0: link up (1000Mbps/Full duplex)
[ 9.080000] eth0: link down
[ 11.680000] NET: Registered protocol family 10
[ 11.690000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.710000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2
[ 11.720000] Backport generated by backports.git backports-20141023-2-g4ff890b
[ 11.730000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.750000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
[ 11.790000] xt_time: kernel timezone is -0000
[ 11.830000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.830000] cfg80211: World regulatory domain updated:
[ 11.840000] cfg80211: DFS Master region: unset
[ 11.840000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.850000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.860000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.870000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.880000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.890000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 11.900000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.900000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.910000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.990000] PPP generic driver version 2.4.2
[ 12.000000] NET: Registered protocol family 24
[ 12.050000] ath: EEPROM regdomain: 0x0
[ 12.050000] ath: EEPROM indicates default country code should be used
[ 12.050000] ath: doing EEPROM country->regdmn map search
[ 12.050000] ath: country maps to regdmn code: 0x3a
[ 12.050000] ath: Country alpha2 being used: US
[ 12.050000] ath: Regpair used: 0x3a
[ 12.060000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.080000] cfg80211: Calling CRDA for country: US
[ 12.090000] cfg80211: Regulatory domain changed to country: US
[ 12.090000] cfg80211: DFS Master region: FCC
[ 12.100000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.110000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 12.120000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 12.130000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.140000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 12.150000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=2
[ 20.060000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 20.090000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 20.090000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 20.820000] random: nonblocking pool is initialized
[ 22.090000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.110000] device eth0 entered promiscuous mode
[ 22.110000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 22.220000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 23.690000] eth0: link up (1000Mbps/Full duplex)
[ 23.690000] br-lan: port 1(eth0) entered forwarding state
[ 23.700000] br-lan: port 1(eth0) entered forwarding state
[ 23.700000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.790000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.700000] br-lan: port 1(eth0) entered forwarding state
[ 51.300000] done.
[ 51.300000] jffs2: notice: (930) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 107.710000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 107.720000] device wlan0 entered promiscuous mode
[ 107.720000] br-lan: port 2(wlan0) entered forwarding state
[ 107.730000] br-lan: port 2(wlan0) entered forwarding state
[ 107.830000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 109.730000] br-lan: port 2(wlan0) entered forwarding state
==========================================================================================
V9和V10.3贴片上R174 C72都少了!换了几个64mb就是没用不知道怎么解决,在二手市场淘了根32m的
HYDU121622ETP-D43能用!
固件链接
8M编辑器固件,附带软件石像QOS,NWAN,USB
带U-BOOT自己改MAC地址http://pan.baidu.com/s/1fN6yU
4M非编辑器固件什么软件都没有http://pan.baidu.com/s/1o6Nyy50
不死U-BOOT http://pan.baidu.com/s/1o6A7jPg
ART无线驱动 http://pan.baidu.com/s/1eQu8zPC
老手看看为什么64M就是不行??
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册
x
|