【实用可玩、永久免费】colorbox固件，支持脱机、手机视频、手机管理，持续更新

damings

收藏。。。。

象象

品种资源 发表于 2014-1-3 09:27
要用这个要先刷open wrt固件吗？路由器是nw762，

你支持装ipk插件包也可以，当然也可以刷colorbox的完整固件

象象

jason00fa 发表于 2014-1-2 14:38
刷你的固件都要手动挂载硬盘吗？

ntfs貌似要手工挂载,其他分区格式的不用

无线大菜鸟

似懂非懂

jason00fa

象象 发表于 2014-1-3 14:13
ntfs貌似要手工挂载,其他分区格式的不用

我试了下貌似FAT32也挂不上，应该还少什么插件

alantao

界面看着挺简单，有冲动把尘封的rg100拿来试试

jason00fa

[    0.000000] Linux version 3.10.24 (michael@Dot80Server) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38980) ) #4 Fri Dec 27 19:03:38 CST 2013
[    0.000000] MyLoader: sysp=01000508, boardp=00840082, parts=21080000
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9130 rev 2
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802d49b0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR941ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61464k/65536k available (2183k kernel code, 4072k reserved, 417k data, 276k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] bdinfo: fac txt empty, use default.
[    0.100000] MIPS: machine is TP-LINK TL-WR941ND
[    0.340000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.360000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.370000] TCP: Hash tables configured (established 512 bind 512)
[    0.370000] TCP: reno registered
[    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] NET: Registered protocol family 1
[    0.390000] PCI: CLS 0 bytes, default 32
[    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.430000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.470000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.470000] console [ttyS0] enabled, bootconsole disabled
[    0.490000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.500000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.500000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.510000] 5 tp-link partitions found on MTD device spi0.0
[    0.510000] Creating 5 MTD partitions on "spi0.0":
[    0.520000] 0x000000000000-0x000000020000 : "u-boot"
[    0.520000] 0x000000020000-0x000000106400 : "kernel"
[    0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.540000] 0x000000106400-0x0000007f0000 : "rootfs"
[    0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.560000] mtd: device 2 (rootfs) set to be root filesystem
[    0.570000] 1 squashfs-split partitions found on MTD device rootfs
[    0.570000] 0x0000006e0000-0x0000007f0000 : "rootfs_data"
[    0.580000] 0x0000007f0000-0x000000800000 : "art"
[    0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.610000] libphy: ag71xx_mdio: probed
[    0.920000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
[    0.920000] TCP: cubic registered
[    0.930000] NET: Registered protocol family 17
[    0.930000] Distributed Switch Architecture driver version 0.1
[    0.940000] eth0[0]: detected a Marvell 88E6060 switch
[    0.950000] libphy: dsa slave smi: probed
[    0.960000] 8021q: 802.1Q VLAN Support v1.8
[    0.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.980000] Freeing unused kernel memory: 276K (802eb000 - 80330000)
[    4.790000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[    4.790000] eth0: link up (100Mbps/Full duplex)
[    6.280000] usbcore: registered new interface driver usbfs
[    6.290000] usbcore: registered new interface driver hub
[    6.300000] usbcore: registered new device driver usb
[    6.340000] SCSI subsystem initialized
[    6.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.360000] ehci-platform: EHCI generic platform driver
[    6.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.380000] uhci_hcd: USB Universal Host Controller Interface driver
[    6.390000] usbcore: registered new interface driver usb-storage
[    7.450000] eth0: link down
[    9.880000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[    9.910000] Linux video capture interface: v2.00
[    9.930000] u32 classifier
[    9.940000]     input device check on
[    9.940000]     Actions configured
[    9.950000] Mirror/redirect action on
[    9.970000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[    9.990000] fuse init (API version 7.22)
[    9.990000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[   10.000000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[   10.050000] usbcore: registered new interface driver usblp
[   10.060000] uvcvideo: Unable to create debugfs directory
[   10.060000] usbcore: registered new interface driver uvcvideo
[   10.070000] USB Video Class driver (1.1.1)
[   10.310000] xt_time: kernel timezone is -0000
[   10.350000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.440000] PPP generic driver version 2.4.2
[   10.460000] NET: Registered protocol family 24
[   10.560000] ath: EEPROM regdomain: 0x0
[   10.560000] ath: EEPROM indicates default country code should be used
[   10.560000] ath: doing EEPROM country->regdmn map search
[   10.560000] ath: country maps to regdmn code: 0x3a
[   10.560000] ath: Country alpha2 being used: US
[   10.560000] ath: Regpair used: 0x3a
[   10.580000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   10.610000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
[   10.620000] cfg80211: Calling CRDA to update world regulatory domain
[   10.640000] cfg80211: World regulatory domain updated:
[   10.650000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.660000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.670000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.670000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.680000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   10.690000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[   10.700000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[   10.700000] cfg80211: Calling CRDA for country: US
[   10.780000] cfg80211: Regulatory domain changed to country: US
[   10.780000] cfg80211:  DFS Master region FCC
[   10.790000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.790000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   10.800000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
[   10.810000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[   10.820000] cfg80211:   (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
[   10.820000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
[   10.830000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
[   10.840000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[   19.620000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[   19.620000] eth0: link up (100Mbps/Full duplex)
[   19.620000] device lan1 entered promiscuous mode
[   19.630000] device eth0 entered promiscuous mode
[   19.650000] device lan2 entered promiscuous mode
[   19.710000] device lan3 entered promiscuous mode
[   19.770000] device lan4 entered promiscuous mode
[   20.040000] dsa dsa.0 lan1: link up, 100 Mb/s, full duplex, flow control disabled
[   20.040000] br-lan: port 1(lan1) entered forwarding state
[   20.050000] br-lan: port 1(lan1) entered forwarding state
[   22.050000] br-lan: port 1(lan1) entered forwarding state
[   23.020000] device wlan0 entered promiscuous mode
[   23.020000] br-lan: port 5(wlan0) entered forwarding state
[   23.030000] br-lan: port 5(wlan0) entered forwarding state
[   25.030000] br-lan: port 5(wlan0) entered forwarding state
[   29.480000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   29.520000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   29.520000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[   39.360000] jffs2: notice: (1330) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  492.520000] device wlan0 left promiscuous mode
[  492.520000] br-lan: port 5(wlan0) entered disabled state
[  532.170000] eth0: link down
[  532.190000] br-lan: port 1(lan1) entered disabled state
[  532.190000] device lan4 left promiscuous mode
[  532.200000] br-lan: port 4(lan4) entered disabled state
[  532.210000] device lan3 left promiscuous mode
[  532.210000] br-lan: port 3(lan3) entered disabled state
[  532.210000] device lan2 left promiscuous mode
[  532.220000] br-lan: port 2(lan2) entered disabled state
[  532.230000] device lan1 left promiscuous mode
[  532.230000] device eth0 left promiscuous mode
[  532.230000] br-lan: port 1(lan1) entered disabled state
[  532.280000] ar71xx: pll_reg 0xb8050014: 0x13000a44
[  532.280000] eth0: link up (100Mbps/Full duplex)
[  532.280000] device lan1 entered promiscuous mode
[  532.290000] device eth0 entered promiscuous mode
[  532.310000] br-lan: port 1(lan1) entered forwarding state
[  532.310000] br-lan: port 1(lan1) entered forwarding state
[  532.340000] device lan2 entered promiscuous mode
[  532.380000] device lan3 entered promiscuous mode
[  532.390000] device lan4 entered promiscuous mode
[  534.310000] br-lan: port 1(lan1) entered forwarding state
[  535.900000] wlan0: authenticate with 38:83:45:5b:6b:04
[  535.920000] wlan0: send auth to 38:83:45:5b:6b:04 (try 1/3)
[  535.930000] wlan0: authenticated
[  535.950000] wlan0: associate with 38:83:45:5b:6b:04 (try 1/3)
[  535.960000] wlan0: RX AssocResp from 38:83:45:5b:6b:04 (capab=0x431 status=0 aid=1)
[  535.970000] wlan0: associated

象象

jason00fa 发表于 2014-1-3 20:42
[    0.000000] Linux version 3.10.24 (michael@Dot80Server) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4. ...

没有看识别硬盘的信息呢，ls  /dev/sd，看下有没得设备

象象

jason00fa 发表于 2014-1-3 20:42
[    0.000000] Linux version 3.10.24 (michael@Dot80Server) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4. ...

一般情况下插上硬盘会有：
[10620.000000] usb 1-1: USB disconnect, device number 2
[10634.840000] usb 1-1: new high-speed USB device number 3 using dwc_otg
[10635.070000] usb-storage 1-1:1.0: USB Mass Storage device detected
[10635.080000] usb-storage 1-1:1.0: Quirks match for vid 0bc2 pid 2300: 200000
[10635.120000] scsi1 : usb-storage 1-1:1.0
[10636.130000] scsi 1:0:0:0: Direct-Access     Seagate  Portable         0130 PQ: 0 ANSI: 4
[10636.150000] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[10636.170000] sd 1:0:0:0: [sda] Write Protect is off
[10636.180000] sd 1:0:0:0: [sda] No Caching mode page found
[10636.190000] sd 1:0:0:0: [sda] Assuming drive cache: write back
[10636.210000] sd 1:0:0:0: [sda] No Caching mode page found
[10636.220000] sd 1:0:0:0: [sda] Assuming drive cache: write back
[10636.270000]  sda: sda1
[10636.280000] sd 1:0:0:0: [sda] No Caching mode page found
[10636.290000] sd 1:0:0:0: [sda] Assuming drive cache: write back
[10636.300000] sd 1:0:0:0: [sda] Attached SCSI disk

jason00fa

没有识别！我刷其他的固件，内核里可以识别，FAT32和NTFS的试过了！明天我试下EXT3的！还有我保存几步以后就不能保存了，就是修改了，保存应用后，还是跳回修改前的配置，可能是满了，我的841V3是8M闪存，64M内存的。刷的是你27号的完整固件版

jason00fa

还有能不能把AIRA2 更新到1.8？听说CPU占用少

象象

jason00fa 发表于 2014-1-4 15:47
还有能不能把AIRA2 更新到1.8？听说CPU占用少

给个链接吧，我集成试试