求救，whr hp g300n TTL 救砖

wwn8856

求救，whr hp g300n TTL 救砖 ，碰到以下问题,如何解决？

ar7240> tftpboot 80f00000 300.enc
Using eth1 device
TFTP from server 192.168.11.2; our IP address is 192.168.11.1
Filename '300.enc'.
Load address: 0x80f00000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Using eth1 device
TFTP from server 192.168.11.2; our IP address is 192.168.11.1
Filename '300.enc'.
Load address: 0x80f00000
Loading: T T T T T T T T T T
TFTP from server 192.168.11.2; our IP address is 192.168.11.1
Filename '300.enc'.
Load address: 0x80f00000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Using eth1 device
TFTP from server 192.168.11.2; our IP address is 192.168.11.1
Filename '300.enc'.
Load address: 0x80f00000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

wwn8856

补充


ar7240> printenv
bootargs=console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:248k(u-boot),8k(u-boot-env),896k(uImage),2816k(rootfs),64k(NVRAM),64k(ART)
bootcmd=bootm BF040000
baudrate=115200
ethaddr=02:AA:BB:CCD:1C
ipaddr=192.168.11.1
serverip=192.168.11.2
tmp_ram=80F00000
tmp_bottom=81F00000
fw_eaddr=BF040000 BF3EFFFF
uboot_eaddr=BF000000 BF03DFFF
u_fw=erase $fw_eaddr; cp.b $fileaddr BF040000 $filesize; bootm BF040000;
ut_fw=tftp $tmp_ram firmware.bin; erase $fw_eaddr; cp.b $fileaddr BF040000 $filesize; bootm BF040000;
ut_uboot=tftp $tmp_ram u-boot.bin; protect off $uboot_eaddr; erase $uboot_eaddr; cp.b $fileaddr BF000000 $filesize;
melco_id=RD_BB09017
hw_rev=0
tftp_wait=4
uboot_ethaddr=02:AA:BB:CCD:1C
DEF-p_wireless_ath0_11bg-authmode=psk
DEF-p_wireless_ath0_11bg-crypto=tkip+aes
DEF-p_wireless_ath0_11bg-authmode_ex=mixed-psk
custom_id=0
buf_ver=1.00
region=AP
build_date=Apr 30 2009 - 10:08:46
pincode=68584962
DEF-p_wireless_ath0_11bg-wpapsk=rf3eaf0yuep6a
buf_crc=E9C6059E
accept_open_rt_fmt=1
stdin=serial
stdout=serial
stderr=serial
loadaddr=80F00000
ethact=eth1
Environment size: 1102/8188 bytes

wwn8856

启动时的信息


BUFFALO U-BOOT Ver 1.00
AP93 (ar7240) U-boot
sri
=====================================================================================================================================
  TAP CALC (read_cnt=512)
----+--------------------------------------------------------------------------------------------------------------------------------
TAP |   0   1   2   3   4   5   6   7   8   9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31
----+--------------------------------------------------------------------------------------------------------------------------------
FAIL|                               0   0   0   0   0   0   0   0   0   0   0 51 5122 512 512 512 512 512 512 512 512 512 512 512 512
----+--------------------------------------------------------------------------------------------------------------------------------
SELECT tap0=9 / tap1=9
#### ddr registers
  B8000000 = C7BC8CD0
  B8000004 = 9DD0E6A8
  B8000008 = 00000033
  B800000C = 00000002
  B8000010 = 00000000
  B8000014 = 00004AF0
  B8000018 = 000000FF
  B800001C = 00000009
  B8000020 = 00000009
  B8000024 = 00000005
  B8000028 = 00000005

32 MB
Memory Test (address line)
Memory Test start(0xA0000000) end(0xA2000000) size(33554432)
Data line test start:0xa0000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0000000 len:0x2000000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:5
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
fill Pattern 0000FFFF  Writing...   Reading...
fill Pattern FFFF0000  Writing...   Reading...
fill Pattern AAAAAAAA  Writing...   Reading...
Top of RAM usable for U-Boot at: 82000000
Reserving 294k for U-Boot at: 81fb4000
Reserving 136k for malloc() at: 81f92000
Reserving 44 Bytes for Board Info at: 81f91fd4
Reserving 36 Bytes for Global Data at: 81f91fb0
Reserving 128k for boot params() at: 81f71fb0
Stack Pointer at: 81f71f98
Now running in RAM - U-Boot at: 81fb4000
id read 0x100000ff
flash size 8388608, sector count = 2048
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  81F71FB0 - 82000000
Memory Test start(80000000) end(81F00000) size(01F00000)
Pattern 00000000  Writing...  Reading...
Memory Test OK
### buf_ver=[1.00] U-Boot Ver.=[1.00]
### build_date(env)=[Apr 30 2009 - 10:08:46] build_date(bin)=[Apr 30 2009 - 10:08:46]
ag7240_enet_initialize...
Reading MAC Address from ENV(0x81f922d9)
: cfg1 0xf cfg2 0x7014
eth0: 02:aa:bb:cc:dd:1c
eth0 up
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0  02:AA:BB:CCD:1C
, eth1  00:03:7F:09:0B:AD

tftp server(receive) go, waiting:4[sec]
Load address: 0x80f00000

aiyundetianshi

我的也成砖了，但是我看不懂。

li28

你的whr-hp-300n现在怎样？我的也跟你同样情况？

li28

ttl后和你的一样，这种情况ar7240>是不是已进了CFE？但又不能TFTP刷?

然后七年

tftp server能正常启动、那就是可以tftp刷的啊、