COMBA AP2400-l拆机

joyoung

AR9341+16M+128M+功放，小黄豆胆电容供电（POE供电被省略了），板载TTL口

正面背面各有一颗64M内存 46V64M8

功放，16M FLASH，1xUSB+TF读卡器，居然还有3个FLASH位置，具备板载4系统实力？

可惜这些USB功能WEB管理界面都看不到，请教TTL刷机方法

ysh259

编程器固件走起

xiaoxiao116

看着做工挺好的

below63

看着少了很多零件不舒服

joyoung

问一条口令，ttl线＋tftp刷openwrt，16m闪存，erase后面的地址如何写
网上教程大多是4m或8m的，我的路由9341，16m闪存，不知对应的地址如何写


U-Boot 1.1.4.21-MULT (May 19 2015 - 10:10:37)

U-boot AP123
DRAM:  ***comba***: watchdog on!

sri
Wasp 1.1
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf [0x0 - 0x1f]
Setting 0xb8116290 to 0x68d02d0f
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 275k for U-Boot at: 87fb8000
Reserving 192k for malloc() at: 87f88000
Reserving 44 Bytes for Board Info at: 87f87fd4
Reserving 36 Bytes for Global Data at: 87f87fb0
Reserving 128k for boot params() at: 87f67fb0
Stack Pointer at: 87f67f98
Now running in RAM - U-Boot at: 87fb8000
id read 0x100000ff
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
Fetching MAC Address from 0x87fe6d08
Fetching MAC Address from 0x87fe6d08
wasp  reset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: 00:27:1d:22:3e:d1
s27 reg init
unit0:s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 00:27:1d:22:3e:d2
unit1:s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
***comba***: watchdog off!
Hit any key to stop autoboot:  0
u-boot> printenv
bootargs=board=BXU2000n-2-A1 console=ttyS0,115200 root=31:03 mtdparts=spi0.0:256k(uboot)ro,64k(ubte      nv)ro,1408k(kernel),6528k(rootfs),1408k(kernel-b)ro,6528k(rootfs-b)ro,64k(cfg),64k(pinfo),64k(art)r      o,7936k@0x50000(firmware) rootfstype=squashfs noinitrd
bootcmd=bootm 0x9f050000
bootdelay=4
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.197.2
serverip=192.168.197.241
dir=
bc=ap123
lu=tftp 0x80060000 u-boot_${bc}.bin&&erase 0x9f000000 +$filesize;cp.b $fileaddr 0x9f000000 $filesiz      e
lf=tftp 0x80060000 ${dir}${bc}-jffs2&&erase 0x9f160000 +$filesize;cp.b $fileaddr 0x9f160000 $filesi      ze
lk=tftp 0x80060000 ${dir}vmlinux_${bc}.lzma.uImage&&erase 0x9f050000 +$filesize;cp.b $fileaddr 0x9f      050000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
bootargsfw1=console=ttyS0,115200 root=31:04 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:2      56k(boot),64k(env),128k(swap),1024k(k1),5120k(r1),1472k(mnt1),1024k(k2),5120k(r2),1472k(mnt2),576k(      rev),64k(cfg),64k(eeprom)
bootargsfw2=console=ttyS0,115200 root=31:07 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:2      56k(boot),64k(env),128k(swap),1024k(k1),5120k(r1),1472k(mnt1),1024k(k2),5120k(r2),1472k(mnt2),576k(      rev),64k(cfg),64k(eeprom)
bootcmdfw1=bootm 0x9f070000
bootcmdfw2=bootm 0x9f7e0000

Environment size: 1280/65532 bytes
u-boot>

孤独的追风

输入printenv来查看下U-Boot默认的连接IP和网关IP
16M:
刷编程器固件：
tftp 0x80000000 full.bin
erase 0xBF000000 +0x1000000
cp.b 0x80000000 0xBF000000 0x1000000
刷uboot：
tftp 0x80000000 uboot.bin
erase 0xBF000000 +0x20000
cp.b 0x80000000 0xBF000000 0x20000
刷固件：
tftp 0x80000000 固件.bin
erase 0xBF020000 +0xFC0000
cp.b 0x80000000 0xBF020000 0xFC0000
刷art:
tftp 0x80000000 art.bin
erase 0xBFFF0000 +0x10000
cp.b 0x80000000 0xBFFF0000 0x10000

joyoung

多谢，先刷了uboot，再进uboot里刷了openwrt

dfyd007

单U搞定所有功能，价格在150人民币以内吧？
电源DC插头那边有那么多元件空位是设计师梦游了么？