少尉
- 注册时间
- 2013-2-11
- 金币
- 417 个
- 威望
- 0 个
- 荣誉
- 0 个
累计签到：16 天
连续签到：0 天
[LV.20]漫游旅程
|
本帖最后由 海南风 于 2015-8-30 13:16 编辑
原厂固件TTL信息：
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-104.4 for BCM96328 (32bit,SP,BE)
Build Date: Mon Apr 11 18:03:41 CST 2011 (zfjimmy@SWD140)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L3205D, id 0xc216 size 4096KB
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Check Reset Default Hold [0|1] : 0
Board Id (0-3) : 96328avng
Number of MAC Addresses (1-32) : 11
Base MAC Address : b0:75:d5:64:4f:4d
PSI Size (1-64) KBytes : 48
Main Thread Number [0|1] : 0
User Password : "y2put"
WLAN SSID Paramters : "ChinaNet-RQp4,ihucydmp"
Device Serial Number : "33200B075D5644F4D"
Device Production Batch : "20100831"
Device Production Date : "20100831"
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8020000) ...
Read flash at blk[2]
Code Address: 0x80010000, Entry Address: 0x80248000
Decompression OK!
Entry at 0x80248000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80248000
Linux version 2.6.21.5 (songlei@SWD150) (gcc version 4.2.3) #1 Fri Apr 22 15:44:00 CST 2011
HS Serial flash device: name MX25L3205D, id 0xc216 size 4096KB
96328avng prom init
CPU revision is: 0002a075
Determined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
On node 0 totalpages: 7936
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 30 pages used for memmap
Normal zone: 3810 pages, LIFO batch:0
Built 1 zonelists. Total pages: 7874
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28900k/31744k available (1971k kernel code, 2844k reserved, 296k data, 92k init, 0k
highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
Calibrating delay loop... 318.46 BogoMIPS (lpj=159232)
Mount-cache hash table entries: 512
wait instruction: enabled
NET: Registered protocol family 16
Total Flash size: 4096K with 64 sectors
File system address: 0xb8020100
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: 10f00000-10ffffff
PREFETCH window: disabled.
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
*** Restore to Factory Default Setting ***
*** Restore to Factory Default Setting ***
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 22 2011 15:42:33
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 92k freed
init started: BusyBox v1.00 (2011.04.22-07:45+0000) multi-call binary
BusyBox v1.00 (2011.04.22-07:45+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
IPv6: add_dev failed for dsl0
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 22 2011 15:42:27
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
Set RGMII delay Programming
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: B0:75 5:64:4F:4D
eth1: MAC Address: B0:755:64:4F:4D
eth2: MAC Address: B0:755:64:4F:4D
eth3: MAC Address: B0:755:64:4F:4D
Enter ethsw_force_mii_mode()!
eth0 Link UP 100 mbps full duplex
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.104.0.cpe4.404.ct.2(WLTEST)
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
p8021ag: p8021ag_init entry
===== Release Version 4.02L.02 (build timestamp 110422_1544) =====
Adjust WLAN Configuration, has configuration [1], num [4], defaultnum [4]
nvramRestore=1
restore param(SSID, PSK, username etc) from nvram
config saved.
nf_conntrack version 0.5.0 (248 buckets, 1984 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
iptables v1.3.8: can't initialize iptables table `filter': Table does not exist (do you
need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
enable l2tp alg
insmod: cannot insert `/lib/modules/2.6.21.5/kernel/net/netfilter/nf_conntrack_ftp.ko':
Success (17): Success
insmod: cannot insert `/lib/modules/2.6.21.5/kernel/net/ipv4/netfilter/nf_nat_ftp.ko':
Success (17): Success
/bin/logctl -r
read log from flash (uncompress: 4627 bytes, compress: 0 bytes)
udhcp server (v0.9.6) started. pid[252], ppid[134]
interface atm1 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
interface atm2 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
enable port snooping failed: No such device or address
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth1 entered promiscuous mode
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
BcmAdsl_Initialize=0xC01636E8, g_pFnNotifyCallback=0xC0183CC4
udhcp handle msg...
files.c,625
files.c,625
files.c,625
DHCP server enable, backup server disable, msg src[1]
pSdramPHY=0xA1FFFFF8, 0x114D1 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=489248
AdslCoreHwReset: AdslOemDataAddr = 0xA1F69DD4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
bcmxtmrt: MAC address: b0 75 d5 64 4f 4f
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
ssk:error:19.405:mdm_getObjectPointer:3312:Could not find instance for
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.X_CT-
COM_DHCPOPTION125.{i}. {1,1,1,1}
ssk:error:19.406:mdm_getObjectPointer:3312:Could not find instance for
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.X_CT-
COM_DHCPOPTION60.{i}. {update igmp snooping port info
1,1,1,1}
[rcl_WanConnectionStateChangeNotify, 864][IP][SETUP]new ServiceList[TR069]
Error at net/bridge/br_ioctl.c,703 old_deviceless can't find br0
brctl cmd -p fdb:atm1:eth1
Error at net/bridge/br_ioctl.c,691 old_deviceless can't find br0
bcmxtmrt: MAC address: b0 75 d5 64 4f 50
update igmp snooping port info
brctl cmd -p fdb:atm1:eth1
Error at net/bridge/br_ioctl.c,691 old_deviceless can't find br0
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Illegal target name.
Bad chain.
Chain (null) doesn't exist.
bcmxtmrt: MAC address: b0 75 d5 64 4f 51
update igmp snooping port info
brctl cmd -p fdb:atm1:eth1
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Illegal target name.
Bad chain.
Chain (null) doesn't exist.
update igmp snooping port info
[brctl mldenableportsnooping 1]
[brctl enableproxymode br0 1]
[brctl enableportsnooping 1]
[brctl mldenableproxymode br0 1]
brctl enableproxymode br0 1 > /dev/null
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Broadcom Packet Flow Cache Char Driver v2.1 Dec 9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec 9 2009 10:05:56
Illegal target name.
Bad chain.
Chain (null) doesn't exist.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
killall bftpd
killall: bftpd: no process killed
iptables v1.3.8: can't initialize iptables table `nat': Table does not exist (do you need
to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.3.8: can't initialize iptables table `nat': Table does not exist (do you need
to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Bad argument `tcp'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `udp'
Try `iptables -h' or 'iptables --help' for more information.
WLmngr Daemon is running
optarg=0 shmId=0
wlmngr.c::wlmngr_init@437 Adapter idx=0
Lock reading WLAN Object
wlReadMdmOne(). idx=0
reading WLAN Object[0], m_instance_wl = 412030
wlmdm wlReadBaseCfg enter objId=1
wlmdm wl_utils_convert_BasicDataTransmitRates_to_wlBasicRate enter basicDataTransmitRates
=54 wlBand = 2 wlgMode = 1
wlmdm wl_utils_convert_MaxBitRate_to_wlRate enter maxBitRate = Auto wlBand=2 wlgMode=1
wlmdm wlReadMimoCfg enter
wlMimoCfgObj->wlNBand=2
wlReadIntfCfg(). bss=0
wlReadAndMappingWLANSecurityConfig. wlAuthMode=psk, wlWpa=aes, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=1
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlReadIntfCfg(). bss=1
wlReadAndMappingWLANSecurityConfig. wlAuthMode=open, wlWpa=tkip, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=2
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlReadIntfCfg(). bss=2
wlReadAndMappingWLANSecurityConfig. wlAuthMode=open, wlWpa=tkip, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=3
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlReadIntfCfg(). bss=3
wlReadAndMappingWLANSecurityConfig. wlAuthMode=open, wlWpa=tkip, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=4
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlmdm wlReadStaticWdsCfg enter
wlmdm wlReadWdsCfg enter
func= web_main,line = 2152
get CMS_MSG_HTTPD_SAVE_CONFIG
wlmngr_NvramMapping enter. @1439
lanIpAddrOfDevice is 192.168.1.1
Richard, get CMS_MSG_RST_BTN_PUSHED
WEBUI Operation WPS Type is NONE, interface number is [1]
WEBUI Operation WPS Type is NONE, interface number is [2]
WEBUI Operation WPS Type is NONE, interface number is [3]
WEBUI Operation WPS Type is NONE, interface number is [4]
There is no Predefined DevicePin in CFE
WPS Device PIN = 10009321
wlmngr.c::wlmngr_setup@834 Adapter idx=0
wlctl -i wl0 phy_watchdog 0
wlmngr_genWscRandSssidPsk@2878 wl_unit=0 unit=0 subunit=0 idx=0
mode_str=wl0_wps_mode
config_str=wl0_wps_config_state
ir_str=wl_wps_reg
NVRAM: wl0_wps_mode=[enabled] wl_wps_reg=[] wl0_wps_config_state=[1]
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
/bin/logctl -w
wlctl -i wl0 wds none
wlctl -i wl0 up
wlctl -i wl0 down
wlctl -i wl0 mbss 0
wlctl -i wl0 bss -C 0 down
wlctl -i wl0 bss -C 1 down
wlctl -i wl0 bss -C 2 down
wlctl -i wl0 bss -C 3 down
wlctl -i wl0 ssid -C 0 'C''h''i''n''a''N''e''t''-''R''Q''p''4'
Setting SSID: "ChinaNet-RQp4"
wlctl -i wl0 ssid -C 1 'C''h''i''n''a''N''e''t''-''D''B''2'
Setting SSID: "ChinaNet-DB2"
wlctl -i wl0 ssid -C 2 'C''h''i''n''a''N''e''t''-''D''B''3'
Setting SSID: "ChinaNet-DB3"
wlctl -i wl0 ssid -C 3 'C''h''i''n''a''N''e''t''-''D''B''4'
Setting SSID: "ChinaNet-DB4"
can't get Addr: Cannot assign requested address
wlctl -i wl0 cur_etheraddr B0:755:64:4F:4E 2>/dev/null
wlctl -i wl0.1 cur_etheraddr 62:75:d5:64:4f:4f 2>/dev/null
wlctl -i wl0.2 cur_etheraddr 62:75:d5:64:4f:4c 2>/dev/null
wlctl -i wl0.3 cur_etheraddr 62:75:d5:64:4f:4d 2>/dev/null
wlctl -i wl0 ap 1
wlctl -i wl0 infra 1
wlctl -i wl0 closed 0
wlctl -i wl0 country CN
wlctl -i wl0 band b
wlctl -i wl0 regulatory 0
wlctl -i wl0 radar 0 2>/dev/null
wlctl -i wl0 spect 0 2>/dev/null
wlctl -i wl0 nmode -1
wlctl -i wl0 mimo_bw_cap 1
wlctl -i wl0 wpa_cap -C 0 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 0 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 1 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 1 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 2 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 2 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 3 > /var/wpa_cap0
wlctl: Unsupported
atm0: no IPv6 routers present
The system is going down NOW !!
Sending SIGTERM to all processes.
Exiting Syslogd!
brctl enableproxymode br0 0 > /dev/null
Please stand by while rebooting the system.
Restarting system.（原厂固件到这里又重启，反复多次，原因不明）
HELO
CPUI |
|
IP卡
狗仔卡
发表于 2015-8-30 13:08
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
千斤顶
显身卡