少尉
- 注册时间
- 2010-3-12
- 金币
- 206 个
- 威望
- 2 个
- 荣誉
- 1 个
累计签到：7 天
连续签到：0 天
[LV.20]漫游旅程
|
晕！ 无法上传图片了。
U-Boot 1.1.3 (Feb 24 2011 - 11:48:14)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb0000
flash_protect ON: from 0xBC000000 to 0xBC01DD63
flash_protect ON: from 0xBC030000 to 0xBC030FFF
============================================
Ralink UBoot Version: 3.5.0.0
--------------------------------------------
ASIC 3883_MP (MAC to 100SW Mode)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: NOR Flash
Date:Feb 24 2011 Time:11:48:14
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 500 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
Image Name: WILI-S.FWBD-1100
Created: 2012-07-10 7:33:58 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 6234125 Bytes = 5.9 MB
Load Address: 80000000
Entry Point: 80290000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80290000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
[4294667.296000] Linux version 2.6.21 (buildd2@builder) (gcc version 4.1.2 20061007 (prerelease)) #1 Tue Jul 10 06:33:36 EEST 2012
[4294667.296000]
[4294667.296000] The CPU feqenuce set to 500 MHz
[4294667.296000] CPU revision is: 0001974c
[4294667.296000] Determined physical RAM map:
[4294667.296000] memory: 04000000 @ 00000000 (usable)
[4294667.296000] Built 1 zonelists. Total pages: 16256
[4294667.296000] Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock4 init=/linuxrc
[4294667.296000] Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
[4294667.296000] Primary data cache 32kB, 4-way, linesize 32 bytes.
[4294667.296000] Synthesized TLB refill handler (20 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (32 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (31 instructions).
[4294667.296000] cause = 40808000, status = 11000000
[4294667.296000] PID hash table entries: 256 (order: 8, 1024 bytes)
[4294667.296000] calculating r4koff... 0007a120(500000)
[4294667.296000] CPU frequency 500.00 MHz
[4294667.296000] Using 250.000 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.297000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[4294667.298000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[4294667.307000] Memory: 62024k/65536k available (2182k kernel code, 3456k reserved, 437k data, 112k init, 0k highmem)
[4294667.325000] Mount-cache hash table entries: 512
[4294667.327000] NET: Registered protocol family 16
[4294667.332000] SCSI subsystem initialized
[4294667.334000] Time: MIPS clocksource has been installed.
[4294667.335000] NET: Registered protocol family 2
[4294667.346000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[4294667.347000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[4294667.348000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.349000] TCP: Hash tables configured (established 2048 bind 2048)
[4294667.350000] TCP reno registered
[4294667.354000] ralink flash device: 0x800000 at 0x1c000000
[4294667.355000] Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
[4294667.356000] Amd/Fujitsu Extended Query Table at 0x0040
[4294667.357000] number of CFI chips: 1
[4294667.358000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
[4294667.359000] Creating 8 MTD partitions on "Ralink SoC physically mapped flash":
[4294667.360000] 0x00000000-0x00030000 : "Bootloader"
[4294667.361000] 0x00030000-0x00040000 : "Config"
[4294667.362000] 0x00040000-0x00050000 : "Factory"
[4294667.363000] 0x00050000-0x00150000 : "Kernel"
[4294667.364000] 0x00150000-0x00650000 : "RootFS"
[4294667.365000] 0x00650000-0x006d0000 : "cfg"
[4294667.366000] 0x006d0000-0x00800000 : "etc"
[4294667.367000] 0x00000000-0x00800000 : "ALL"
[4294667.368000] Load Ralink DFS Timer Module
[4294667.370000] squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
[4294667.370000] squashfs: LZMA suppport for slax.org by jro
[4294667.371000] JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
[4294667.372000] io scheduler noop registered (default)
[4294667.387000] Ralink gpio driver initialized
[4294667.388000] spidrv_major = 217
[4294667.637000] HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
[4294667.638000] N_HDLC line discipline registered.
[4294667.639000] Ralink APSoC Hardware Watchdog Timer
[4294667.640000] Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled
[4294667.641000] serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
294667.642000] serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
[4294667.645000] loop: loaded (max 8 devices)
[4294667.646000] rdm_major = 254
[4294667.647000] MAC_ADRH -- : 0x00000000
[4294667.648000] MAC_ADRL -- : 0x00000000
[4294667.649000] Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
[4294667.650000] NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
[4294667.651000] MAC_ADRH -- : 0x00000019
[4294667.652000] MAC_ADRL -- : 0x3b8279d6
[4294667.653000] PROC INIT OK!
[4294667.654000] PPP generic driver version 2.4.2
[4294667.655000] PPP Deflate Compression module registered
[4294667.656000] PPP BSD Compression module registered
[4294667.657000] PPP MPPE Compression module registered
[4294667.658000] NET: Registered protocol family 24
[4294667.659000] tun: Universal TUN/TAP device driver, 1.6
[4294667.660000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[4294667.666000] block2mtd: version $Revision: 1.1.1.1 $
[4294667.667000] u32 classifier
[4294667.668000] nf_conntrack version 0.5.0 (512 buckets, 4096 max)
[4294667.669000] IPv4 over IPv4 tunneling driver
[4294667.670000] GRE over IPv4 tunneling driver
[4294667.671000] TCP cubic registered
[4294667.672000] NET: Registered protocol family 1
[4294667.673000] NET: Registered protocol family 17
[4294667.674000] Bridge firewalling registered
[4294667.675000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[4294667.676000] All bugs added by David S. Miller <davem@redhat.com>
[4294667.677000] WILI_EEPROM: init
[4294667.678000] WILI_EEPROM: wili_eeprom_read: found eeprom at offset 0x1000
[4294667.679000] Reset button gpio:77 active:0
[4294667.680000] Registered led device: LED1
[4294667.681000] Registered led device: LED2
[4294667.682000] Registered led device: LED3
[4294667.683000] Registered led device: LED4
[4294667.684000] Registered led device: LED5
[4294667.685000] Registered led device: LED6
[4294667.688000] VFS: Mounted root (squashfs filesystem) readonly.
[4294667.689000] Freeing unused kernel memory: 112k freed
[4294667.983000] Algorithmics/MIPS FPU Emulator v1.5
Populating '/etc/' directory structure ... done.
Linking '/usr/etc/*' files under '/etc' ...
done
[4294668.348000] Empty flash at 0x00004984 ends at 0x00004ac0
FWBD-1 series
cannot write to '/etc/oem.cfg', Read-only file system
cannot write to '/etc/oem.cfg', Read-only file system
starting pid 781, tty '': '/etc/rc.d/rc.sysinit'
[4294669.353000] Started WatchDog Timer.
[4294669.354000] Started WatchDog Timer.
[4294669.403000] NIC Link is Down
Waiting for reset to factory defaults packet.
.
...
[4294673.509000] ra2880stop()...Done
cannot write to '/etc/oem.cfg', Read-only file system
cannot write to '/etc/oem.cfg', Read-only file system
starting pid 822, tty '': '/usr/etc/rc.d/rc-bg start'
starting pid 825, tty '/dev/ttyS1': '/sbin/getty -L ttyS1 115200 vt100'
Sat Jan 1 00:00:00 UTC 2011
FH-AP2400-W-5C login: [4294674.506000] calling '/sbin/raconf -r', ret=256
[4294674.720000] device eth0 entered promiscuous mode
[4294674.734000] device ra0 entered promiscuous mode
[4294674.745000] device ra0 left promiscuous mode
[4294674.746000] br0: port 2(ra0) entering disabled state
[4294674.940000] device ra0 entered promiscuous mode
Cannot get current device settings: Operation not supported
not setting autoneg
[4294675.101000] br0: port 2(ra0) entering learning state
Cannot get current device settings: Operation not supported
not setting autoneg
00:00:01 [I] Launched 'sshd' successfully in respawning mode.
ls: /etc/persistent/skins/*.tgz: No such file or directory
00:00:02 [I] Launched 'httpd' successfully in respawning mode.
00:00:02 [I] Launched 'discoveryd' successfully in respawning mode.
[4294676.069000] Ebtables v2.0 registered
[4294676.102000] br0: topology change detected, propagating
[4294676.103000] br0: port 2(ra0) entering forwarding state
Failed to add ebtable rule /sbin/ebtables -t nat -D dc0 --in-interface ra0 -j arpnat --arpnat-target ACCEPT 2> /dev/null
[4294676.387000] ebt_arpnat: module license 'unspecified' taints kernel.
Failed to add ebtable rule /sbin/ebtables -t nat -D dc1 --out-interface ra0 -j arpnat --arpnat-target ACCEPT 2> /dev/null
00:00:02 [I] Launched 'alertd' successfully in respawning mode.
00:00:02 [I] Launched 'ledd' successfully in respawning mode.
00:00:02 [I] Launched 'statsd' successfully in respawning mode.
Reconfiguring syslogged...
00:00:03 [I] Launched 'syslog' successfully in respawning mode.
admin: Boot finished. Ready to serve ...
[4294681.641000] process `alertd' is using obsolete setsockopt SO_BSDCOMPAT
|
|
IP卡
狗仔卡
发表于 2013-10-4 15:53
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
千斤顶
显身卡
进入到 TTL 登录界面了！ 可是又被帐号 密码给卡住了！ 求解？？？
