ar9341改爱快AP 教程

忘了我吧Android

GPIO#17是TP的reset号  GPIO#20是爱快AP的
短接R98就能启动了




一些坛友反应有的板子GPIO20引脚出来的位置不一定是R98
实际是哪自己看看




ART
10000~1FFF0  mac看着改。。




链接: http://pan.baidu.com/s/1slot9xz 密码: duex
ART是847V2的，
要是信号不好换原机的ART，还是不好砸了吧，没什么卵用。。。。。。。。

欢迎加入讨论群  19587213
JS止步， 纯玩家讨论！

yeyeyeye1997

继上一楼。
把R83的IC移到R98之后可以启动了，但是一直无限重启，按回车键之后卡在uboot里。
TTL如下：

1. *********************************************
   
2. *        U-Boot 1.1.4  (Jun 23 2014)        *
   
3. *********************************************
   
4. 
   
5. U-Boot for AR9341 AP
   
6. 
   
7. DRAM:   64 MB DDR 32-bit
   
8. FLASH:  Winbond W25Q128 (16 MB)
   
9. CLOCKS: 560/450/225/28 MHz (CPU/RAM/AHB/SPI)
   
10. 
    
11. Hit any key to stop autobooting:  0
    
12. 
    
13. Searching kernel image from JFFS2...done
    
14. Booting image at: 0x80800000
    
15. 
    
16.    Image name:   MIPS OpenWrt Linux-3.10.49
    
17.    Created:      2015-06-30   7:06:32 UTC
    
18.    Image type:   MIPS Linux Kernel Image (lzma compressed)
    
19.    Data size:    1063005 Bytes = 1 MB
    
20.    Load address: 0x80060000
    
21.    Entry point:  0x80060000
    
22. 
    
23. Uncompressing kernel image... OK!
    
24. Starting kernel...
    
25. 
    
26. [    0.000000] Linux version 3.10.49 (daxiong@ik8.com) (gcc version 4.8.3 (OpenW
    
27. rt/Linaro GCC 4.8-2014.04 unknown) ) #7 Tue Jun 30 15:06:22 CST 2015
    
28. [    0.000000] bootconsole [early0] enabled
    
29. [    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
    
30. [    0.000000] SoC: Atheros AR9341 rev 3
    
31. [    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:25.00
    
32. 0MHz
    
33. [    0.000000] Determined physical RAM map:
    
34. [    0.000000]  memory: 04000000 [url=home.php?mod=space&uid=610341]@[/url] 00000000 (usable)
    
35. [    0.000000] Initrd not found or empty - disabling initrd
    
36. [    0.000000] Zone ranges:
    
37. [    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
    
38. [    0.000000] Movable zone start for each node
    
39. [    0.000000] Early memory node ranges
    
40. [    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
    
41. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    
42. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
    
43. bytes
    
44. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
    
45. es: 16256
    
46. [    0.000000] Kernel command line:  board=COMFAST-AP9341FE console=ttyS0,115200
    
47. mtdparts=spi0.0:64k(u-boot)ro,64k(art)ro,1536k(kernel),14656k(rootfs),64k(nvram
    
48. )ro,16192k@0x20000(firmware) rootfstype=squashfs,jffs2 noinitrd
    
49. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
    
50. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    
51. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    
52. [    0.000000] Writing ErrCtl register=00000000
    
53. [    0.000000] Readback ErrCtl register=00000000
    
54. [    0.000000] Memory: 61208k/65536k available (2252k kernel code, 4328k reserve
    
55. d, 605k data, 276k init, 0k highmem)
    
56. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    
57. [    0.000000] NR_IRQS:51
    
58. [    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
    
59. [    0.070000] pid_max: default: 32768 minimum: 301
    
60. [    0.070000] Mount-cache hash table entries: 512
    
61. [    0.080000] NET: Registered protocol family 16
    
62. [    0.090000] MIPS: machine is COMFAST AP9341FE
    
63. [    0.500000] bio: create slab <bio-0> at 0
    
64. [    0.510000] Switching to clocksource MIPS
    
65. [    0.520000] NET: Registered protocol family 2
    
66. [    0.520000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
    
67. [    0.520000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
    
68. [    0.530000] TCP: Hash tables configured (established 512 bind 512)
    
69. [    0.530000] TCP: reno registered
    
70. [    0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
    
71. [    0.540000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    
72. [    0.550000] NET: Registered protocol family 1
    
73. [    0.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    
74. [    0.570000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
    
75. Y) (c) 2001-2006 Red Hat, Inc.
    
76. [    0.590000] msgmni has been set to 119
    
77. [    0.590000] io scheduler noop registered
    
78. [    0.590000] io scheduler deadline registered (default)
    
79. [    0.600000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
    
80. [    0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
    
81. [    0.640000] console [ttyS0] enabled, bootconsole disabled
    
82. [    0.640000] console [ttyS0] enabled, bootconsole disabled
    
83. [    0.650000] ath79-spi ath79-spi: master is unqueued, this is deprecated
    
84. [    0.660000] m25p80 spi0.0: found w25q128, expected m25p80
    
85. [    0.660000] m25p80 spi0.0: w25q128 (16384 Kbytes)
    
86. [    0.670000] 6 cmdlinepart partitions found on MTD device spi0.0
    
87. [    0.670000] Creating 6 MTD partitions on "spi0.0":
    
88. [    0.680000] 0x000000000000-0x000000010000 : "u-boot"
    
89. [    0.690000] 0x000000010000-0x000000020000 : "art"
    
90. [    0.690000] 0x000000020000-0x0000001a0000 : "kernel"
    
91. [    0.700000] 0x0000001a0000-0x000000ff0000 : "rootfs"
    
92. [    0.710000] mtd: device 3 (rootfs) set to be root filesystem
    
93. [    0.710000] 1 squashfs-split partitions found on MTD device rootfs
    
94. [    0.720000] 0x000000440000-0x000000ff0000 : "rootfs_data"
    
95. [    0.720000] 0x000000ff0000-0x000001000000 : "nvram"
    
96. [    0.730000] 0x000000020000-0x000000ff0000 : "firmware"
    
97. [    0.750000] libphy: ag71xx_mdio: probed
    
98. [    1.310000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd0
    
99. 42, driver=Generic PHY]
    
100. [    1.320000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
     
101. [    1.880000] ag71xx-mdio.1: Found an AR934X built-in switch
     
102. [    2.910000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
     
103. [    2.920000] TCP: cubic registered
     
104. [    2.920000] NET: Registered protocol family 17
     
105. [    2.920000] 8021q: 802.1Q VLAN Support v1.8
     
106. [    2.930000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
     
107. [    2.940000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
     
108. procd: Console is alive
     
109. procd: - watchdog -
     
110. [    4.920000] usbcore: registered new interface driver usbfs
     
111. [    4.930000] usbcore: registered new interface driver hub
     
112. [    4.940000] usbcore: registered new device driver usb
     
113. [    4.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
114. [    4.950000] ehci-platform: EHCI generic platform driver
     
115. [    4.960000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
     
116. procd: - preinit -
     
117. jffs2 is ready
     
118. jffs2 is ready
     
119. [    5.320000] jffs2: notice: (278) jffs2_build_xattr_subsystem: complete buildi
     
120. ng xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead,
     
121. 2 orphan) found.
     
122. switching to overlay
     
123. procd: - early -
     
124. procd: - watchdog -
     
125. procd: - ubus -
     
126. procd: - init -
     
127. Please press Enter to activate this console.
     
128. [    7.510000] Loading modules backported from Linux version master-2014-05-22-0
     
129. -gf2032ea
     
130. [    7.520000] Backport generated by backports.git backports-20140320-37-g5c33da
     
131. 0
     
132. [    7.540000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
     
133. [    7.570000] xt_time: kernel timezone is -0000
     
134. [    7.610000] cfg80211: Calling CRDA to update world regulatory domain
     
135. [    7.610000] cfg80211: World regulatory domain updated:
     
136. [    7.620000] cfg80211:  DFS Master region: unset
     
137. [    7.620000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gai
     
138. n, max_eirp), (dfs_cac_time)
     
139. [    7.630000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 m
     
140. Bm), (N/A)
     
141. [    7.640000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 m
     
142. Bm), (N/A)
     
143. [    7.650000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 m
     
144. Bm), (N/A)
     
145. [    7.660000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000
     
146. mBm), (N/A)
     
147. [    7.670000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000
     
148. mBm), (0 s)
     
149. [    7.670000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000
     
150. mBm), (0 s)
     
151. [    7.680000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 m
     
152. Bm), (N/A)
     
153. [    7.690000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0
     
154. mBm), (N/A)
     
155. [    7.700000] ip_tables: (C) 2000-2006 Netfilter Core Team

复制代码

唧_[VIP]

支持

3ax31a

感谢分享

hengjunjie

谢谢楼主分享

13062678135

感谢楼主分享。

zhaocz

感谢楼主，简单明了，这样的贴子才是精华。

tzbd

zhaocz 发表于 2016-6-13 08:41
感谢楼主，简单明了，这样的贴子才是精华。

说的好啊，呵呵。

wear2003

你的启动不了，是雨水浇了还是怎么的

tzbd

什么也不说了，顶你一下

whw5555

感谢分享

小茅

GPIO17是干嘛用都，不是短接20就能用吗，还有怎么区分S1和H1，功能上又不一样d

15237527724

那个电阻在哪找不到？