[更新2010.07.17]WRV54G(GTWX5715) OpenWrt backfire 10.03中文版。
本帖最后由 lintel 于 2010-7-30 17:11 编辑目前Openwrt支持的版本。
系统:OpenWrt backfire 10.03 （Intel IXP4xx）
支持路由型号:WRV54G(GTWX5715),MI424等。
支持的无线模块:RT2x61,AR5XXX,RTL8187.
网络制式: a/b/g/n
支持的USB设备:USB网卡，USB声卡。USB摄像头，部分3G网卡,RTL8187.
支持的文件系统:EXT2/3/4 ,FAT/NTFS,NFS.
软件支持：
Luci中文。
vsftpd
samba
ushare
miniUPNP
Transmission
等。
其他待续。。。
启动信息：
Linux version 2.6.32.10 (lintel@andLinux) (gcc version 4.3.3 (GCC) ) #17 Tue Jun 29 03:23:06 EDT 2010
CPU: XScale-IXP42x Family revision 1 (ARMv5TE), cr=000039ff
CPU: VIVT data cache, VIVT instruction cache
Machine: Gemtek GTWX5715 (Linksys WRV54G)
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c02aa904, node_mem_map c02bc000
DMA zone: 128 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 16256 pages, LIFO batch:3
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16256
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62108KB available (2500K code, 163K data, 96K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:64
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
pci 0000:00:01.0: reg 10 32bit mmio:
pci 0000:00:02.0: reg 10 32bit mmio:
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: reg 10 32bit mmio:
pci 0000:00:02.1: supports D1 D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.1: PME# disabled
pci 0000:00:02.2: reg 10 32bit mmio:
pci 0000:00:02.2: supports D1 D2
pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.2: PME# disabled
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: dmabounce: registered device
pci 0000:00:02.0: dmabounce: registered device
pci 0000:00:02.1: dmabounce: registered device
pci 0000:00:02.2: dmabounce: registered device
bio: create slab <bio-0> at 0
Switching to clocksource OSTS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
IXP4xx Queue Manager initialized.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)漏 2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8001000 (irq = 13) is a XScale
console enabled
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=64
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x7e0000
5 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 5 MTD partitions on "IXP4XX-Flash.0":
0x000000000000-0x000000080000 : "RedBoot"
0x000000080000-0x000000180000 : "linux"
0x000000180000-0x0000007e0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=720000, len=C0000
0x000000720000-0x0000007e0000 : "rootfs_data"
0x0000007e0000-0x0000007ff000 : "FIS directory"
0x0000007ff000-0x000000800000 : "RedBoot config"
IXP4xx MII Bus: probed
eth0: MII PHY 32 on NPE-B
eth1: MII PHY 5 on NPE-C
i2c /dev entries driver
IXP4xx Watchdog Timer: heartbeat 60 sec
Registered led device: Power
Registered led device: Wireless1
Registered led device: Wireless2
Registered led device: Internet
Registered led device: DMZ
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing init memory: 96K
Please be patient, while OpenWrt loads ...
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
net eth0: firmware: requesting NPE-B
NPE-B: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-B: firmware functionality 0x2, revision 0x2:1
eth0: link up, speed 0 Mb/s, full duplex
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
net eth1: firmware: requesting NPE-C
NPE-C: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-C: firmware functionality 0x5, revision 0x2:1
PPP generic driver version 2.4.2
NET: Registered protocol family 24
eth1: link up, speed 100 Mb/s, full duplex
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
ath: EEPROM regdomain: 0x10
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: CO
ath: Regpair used: 0x10
phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: ath9k-phy0::radio
Registered led device: ath9k-phy0::assoc
Registered led device: ath9k-phy0::tx
Registered led device: ath9k-phy0::rx
phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xc4f80000, irq=28
cfg80211: Calling CRDA for country: CO
cfg80211: Regulatory domain changed to country: CO
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 20000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 20000 KHz), (300 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 20000 KHz), (300 mBi, 3000 mBm)
usbcore: registered new interface driver rtl8187
Slow work thread pool: Starting up
Slow work thread pool: Ready
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NTFS driver 2.1.29 .
loop: module loaded
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ip_tables: (C) 2000-2006 Netfilter Core Team
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: enabling device 0000:00:02.2 (0140 -> 0142)
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: Enabling legacy PCI PM
ehci_hcd 0000:00:02.2: irq 27, io mem 0x48012000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
nf_conntrack version 0.5.0 (972 buckets, 3888 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
xt_time: kernel timezone is -0000
Micrel/Kendin KS8995 Ethernet switch SPI driver version 0.1.1
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: enabling device 0000:00:02.0 (0140 -> 0142)
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 27, io mem 0x48010000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: enabling device 0000:00:02.1 (0140 -> 0142)
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 27, io mem 0x48011000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver snd-usb-audio
usb 3-1: new full speed USB device using ohci_hcd and address 2
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
Linux video capture interface: v2.00
gpio-buttons driver version 0.1.2
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
gspca: main v2.7.0 registered
usbcore: registered new interface driver zc3xx
zc3xx: registered
fuse init (API version 7.13)
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
spi-ks8995 spi32766.0: KS8995 device found, Chip ID:0, Revision:1
scsi 0:0:0:0: Direct-Access GenericExternal 1.03 PQ: 0 ANSI: 4
sd 0:0:0:0: 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 0:0:0:0: Write Protect is off
sd 0:0:0:0: Mode Sense: 21 00 00 00
sd 0:0:0:0: Assuming drive cache: write through
usb-storage: device scan complete
sd 0:0:0:0: Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 0:0:0:0: Assuming drive cache: write through
sd 0:0:0:0: Attached SCSI disk
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
Adding 995988k swap on /dev/sda1.Priority:-1 extents:1 across:995988k
kjournald starting.Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting.Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
IMQ driver unloaded successfully.
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
br-lan: port 2(wlan0) entering disabled state
br-lan: port 1(eth0) entering disabled state
eth0: link down
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
eth1: link down
eth0: link up, speed 0 Mb/s, full duplex
eth0: link down
eth0: link up, speed 0 Mb/s, full duplex
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
eth1: link up, speed 100 Mb/s, full duplex
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
br-lan: port 1(eth0) entering disabled state
eth0: link down
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
eth1: link down
eth0: link up, speed 0 Mb/s, full duplex
eth0: link down
eth0: link up, speed 0 Mb/s, full duplex
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
eth1: link up, speed 100 Mb/s, full duplex
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state 原先的网卡还支持吗？ 版主，能提供wrv54g编译的配置文件吗。多谢。 OpenWrt backfire 10.03 （Intel IXP4xx）系统怎么编译 Mldonkey？
x86的Mldonkey不能用，网上也没有IXP4xx的下载；OpenWrt 如果没有Mldonkey就太遗憾了！ 提供开发环境就好了，WRV54G才能更好用！ 感谢分享！！！ :P:P:P:P:P
页:
[1]